Can anyone remember if there was a thread about a clamp on trailer hitch? Seem like I saw one years ago, but I believe the fellow has passed away. Thanks, smoker
I have a sliding barn type door that I need to secure. The door as well as the building are sided in extruded steel. Is there a hasp that can be purchased to accomplish this or do I need to fab one up? I thought about buying a large strap hinge and having at it, but always check here first for...
Any thoughts or suggestions? Had this 9200 since 1990 and it's really been a great machine. I think HST will be more user friendly as Arthritis has gotten a hold of hands and wrists. Would appreciate any input you all might have. Thanks, smoker
I have a 4'x2' lawn roller that insists on leaking water. Suggestion was to use sand as weight. Have any of you folks used sand and did you fill it full, half full?? Grandson says it will hold ~20 50# bags of sand, I think I would need a
D-9 to pull it:) Appreciate any experiences you can...
Well here I am again asking the you folks for ideas. I have a flag pole that is 2 1/2" in diameter that has a busted pulley. I need to pull this pole to replace it. I have a B9200 with a loader. Thanks in advance, smoker:confused:
I have a Porter Cable 4.5 inch trim saw that is no longer in production. It uses a 4.5 x 3/8 blade, which are very difficult to get. I have a new never used blade that fits the arbor but will not tighten up. Is there a place where I can buy a washer type shim? I'm sure I don't have a thin enough...
Anyone have an idea of how to build a device that would stop my lift arms from rising when using a dump trailer? I am using a 3 point tow bar as the tow bar on the tractor is too low. This is on a Kubota B9200. Thanks in advance, I have an idea but much wiser minds are here. smoker
I have a 6 ton electric DR spliiter. It has the momentary push button power switch and I would like to replace that with a on/off toggle switch. Has anyone done that here? Mine has a capcitor and the original switch has four wires going to it. That confuses me. I called the factory for a little...
Have a 6x10 dump deck over 7K on order and would like to know the proper ball height. I've got an approximate of 20" but would rather get it right. If you have one I would appreciate your input. Thanks, smoker
Has anyone here done this modification? I need to remove the ball hitch that comes with the trailer and install a 6 hole adjustable bracket, the same bracket that comes with larger heavier duty trailers like the Bri-Mar 8x12 dump. That way I can go from an Ag. type clevis hitch back to the ball...
Busted the top link on my post hole digger. Have any of you folks done a repair? I see that CST has a repair swivel eye, ( out of stock ), but it looks like a problem welding a flat to the round stub I have left on mine. Any ideas?
Thanks, smoker
Does anyone have a B9200 with rear ag tires? I am in need of the size tires that you are using. Really would appreciate any help someone might give. Thanks, smoker
Sure hate to beat this valve thing to death but I searched for this and couldn't find anything. My question is, how can I stop the detent function on my Speeco splitter control valve? I'm constantly having to pop this valve out of detent. After 200 or 300 cycles......Well you know.
Having bought a dump trailer to help with firewood I needed to convert the ball coupler to implement/ag type hitch. Trailer Enterprises in PA can help. Nice folks, smoker
I have a 22 ton Huskee splitter. I woulkd like to add a few inches of height to the splitting wedge. Seems as though my trees are getting fatter and require me to take two hits to split. Anyone done this? sure would like some input. Called Huskee/Speeco with expected results......NOT! Thanks, smoker
I have a B9200. I would like to build some front end weights. I need just a little weight up front to counter balance when I'm skidding logs. Have any of you folks done this? Thanks, smoker
I have a B9200. I use it for general stuff and am not satisfied with the turf tires it has on it. I use it on my lawns for rolling and general clean up so don't want a tire that would leave cleat marks. Does anyone have experience with a different tread style that might give me a little better...
New here so I'll say hello to all. Came across the plans for bucket forks by MadReferee. Built them using most of his measurements. Project came out very well. Wanted to thank him only to find that he has passed on. I'm sure most of you regulars knew him and just wanted to say Thanks. Regards...