Search results

Anyone have a solution to my screw up it goes as follows. While moving some topsoil with my JD4410 with a 300CX loader I screwed up by bouncing the bucket to remove stuck dirt while traveling foward toward the barn. I had the bucket too low and the ground caught the bucket blade edge and it...

We had a very mild winter and little snow last year in Michigan and only used my JD4410 once and that was probably not necessary. Snow melted in the next few days. My question is that I have old fuel that is at least 12 months old in my tractor. I use the usual fuel additives that many use...

How heavy and at what risk is moving or trying to move a granite rock approx. 3'Dia X 3 1/2' with a John Deere 4410 with a 300CX ? I have a pry bar and maybe some muscle around at the holiday. The 800lb tiller is on the rear from tilling the garden. If the risk to the loader or bucket is...

Why do you mount your tractor and your horse only the left side? A. Horses bite and bronk it mounted on the right. Your horse may convince your tractor to do the same! They are probably in the barn conspiring right now. B. The left side of the brain is for creative endevors, the more you...

The operators manual indicates on many if not all newer and older JD compacts, Yanmar engine at least, that the valve lash should be checked and adjusted at every 500 miles. The proceedure is very time consuming, difficult, and I bet costly if done by the book at a JD dealer. I bet mine with...

I just came in the house my brand new V- belt on my wife's 60" Cub Cadet Zero turn is all chewed up. Now that the leaves are coming down good and heavy I have always helped my wife's mower out by giving it a good run through the heavy leaves. I have been very successful with this for years. I...

While putting on some wheel weights I noticed extensive orange bailing twine twisted around the inside wheel hub. It is near impossible to get it all off. This is a potential problem in that it may work its way into and past the rear wheel seal and cause leakage or damage to the seal. It is...

When you look at the new line up of John Deere 4000 series tractors note the same but slightly different engine on four out of six models. 4120 ******** 4320 ********* 4520 *********** 4720 148.9 cu in **** 148.9 cu in **** 148.9...

Can anyone identify the old deere wheel weights? I am going "GREEN" and trying to recycle old tractor wheel weights. See picture. I went to a neighbor's farm 3 miles away they have so much farm stuff that I was hypnotized. Too many wheel weights to pick from. They had some big daddy deere...

Todays project has come to a halt and I need your help. I am stuck in the middle of a project to change the leaking seal on my left front wheel on my JD4410. Many JD compact tractors are identical or very near to the one pictured. The wheel came off easy with air gun, the hub asm with its...

I recommend most of us "Grandpa's" should write the words "DIESEL FUEL ONLY" on the backside inside of the fuel door. A fine tip white paint pen permanent paint is what is needed. Twice in the last few years I was looking for a good used tractor I came across a tractor that grandpa died and...

While looking for a good used 5' tiller for the 3pt on my 4410 JD I came across a man with an old snow blade that would quick attach to my 300cx loader for 400. It does not have hydro cyl but can be angled and secured with a pin. The unit was made, weldment, from a rear tractor blade years...

I have a 2002 John Deere 4410 e-hydro with a loader controller (joystick) and quick disconnects. I ordered a new 300cx loader from my local John Deere dealer and was told it would come in for my purchase approx 4' cube over 1000lbs. My tractor still has rubber plugs on the sides where the side...

I put a 3pt quick hitch on my 4410 John Deere compact tractor. After about two hours of fighting to get the 1/3yd dump bucket on the new quick release I pulled it off and will sell it for cheep. I believe it may be fast and easy for some impliments but not the first one that I selected. The...

The ash tree bore bugs killed eight 18" to 24" trees by the road and at least two dozen on the five acres that I cut. I payed to have the trees by the road cut and cut most of the others except for the few remaining that may take down the power/tv/phone lines. With all the stumps I must rent a...

I bought a used John Deere 4410 and assumed it was a modern machine that had downward hydrolic power on the three point. I sold an old poor mans Deere an 880 Oliver and it had about 4000lb down or up. Is mine broke or do all JD4410 have no 3-point down power. The Oliver could pick up the rear...