Battery will not charge. No blown fuses K - 5 relay replaced along with voltage regulator. Alternator or generator has 32 volts AC output. Yellow battery light comes on. I have a new voltage regulator in it. Checked the white wire output was 14 volts! Great right? Ran the tractor for about 5...
Every time I release the brake / clutch it quits. I have the seat switch jumped and the two switches the brake/clutch arm stroke work fine. I dont know what else to do?
Im tearing my hair out with this machine! Keeps blowing the 10 amp fuse on the inside of the white fuse block near the coolant reservoir. Then the PTO doesnt work! I have a schematic but only shows 2 fuses and the fuse in the diagram is good. Anybody know where the four fuses in the block go to?
The PTO doesnt work and the furthest away fuse in the block keeps blowing. Im assuming its related to the PTO circuit. Like some info on what each of the four fuses in the block do and the proper amperage. Cant find any info anywhere! Here is a pic 0f the fuse box. Its the last slot missing...
My X300 stalls after anywhere between 10 minutes and 30. In a short period of time starts right up works fine and it stalls again after a short period. I pulled the plugs and they are dry each time look to be burning well. Any help out there?
Got the right belt will not go on. I double checked the number its a JD belt number M44121. does any body know the proper way to install the belt? I found the arm tensioner with the two pulleys on it was bent some. I re bent it to what I think it should be. Does anybody have a good picture...
My X 300 will run and start good. Other times it wont start at all and sometimes just quits while running. I have found out it is spark that goes. I cant seem to find a parts list or diagram to purchase the control unit under the dash or that small module thats mounted in the side of the...
My X 700 wont start. Jumped solenoid turns over easily but no spark. Purple wire on solenoid never gets 12 volts. Tested seat hydro pedal switch and parking switch all good. Blade or pto switch is disengaged. Please help!!!
I am repairing a basket case for a friend LX 176 I replaced a blown motor with a 20.5 briggs I teck I had laying around. I cannot get the PTO and the drive pulley to hook up right. How long is the stock shaft on the engine that is suppose to go in the mower? I don't even know what motor is...
I got a basket case mower to repair for a friend. I think this was not the original motor. I cant find the pulse port for the fuel pump. I have been using the port off the valve cover. I doubt this is the right one because I believe it goes to the air cleaner. Any help greatly appreciated.
Because I cant do anything right the first time I have to split the tractor again. Of course I put new oil in it. Is there any way to do this without draining all the oil back out?
I feel like an idiot but here goes. Replaced the clutch disc on the tractor. New throw out bearing all bolts torqued properly. Still doesn't work. Clutch will not disengage drives well if you start it in gear. Not sure what happened. Pretty pissed after splitting the tractor and all!!!!
Does anybody know how to change and or fill the oil in the front differential of this machine? I dont want to spend the 50 bucks for an owners manual. I have a sort of shop manual and it shows the parts layout but nothing about replacing or filling the oil. Great site and thanks in advance!!!
I have a 1200 I just split to replace clutch. The old disc looks worn but not that bad. Should I replace the throw out bearing and the pressure plate? The throw out bearing wont come out shouldn't it just slide off? Can I use a gear puller for it? Having split the tractor I don't want to...
Anybody give me the readers digest version of how to get to the clutch? I have a manual from the internet and its terrible!! I have done car clutches before so I am pretty good backyard guy. Anybody walk me through it?
I am repairing a John Deere LA 110 for a friend. He got it back from a repair shop in a thousand parts. I guess he blew it up forgetting engines need oil on ocasion! I cannot find an engine anywhere used. Its a 501 CC 19.5 horse motor. Is there another engine I could use? Not worth my time...
I have to replace a clutch in this tractor. I have a CD I downloaded from the internet but it leaves a lot to be desired. Anybody got any tips or tricks or a readers digest version on how to change it? Im a fairly good mechanic and have done car clutches before.
Does anybody know what oil goes in the front differential? Also I am assuming pulling the plug on the front of it and filling till it drips out is the correct way to fill it.
I have a Ford F-1200 tractor. Best I can tell with the serial numbers and engine numbers its a 1982. Anybody know what size clutch I have or where I can get a repair manual? Where is a good reasonable place to get parts?
SN: U201159
ENGINE # LEK 802D 207002