Search results

I probably have one Email me

It could be the splines on the clutch shaft. Clutches usually give signs before failing.

Not a lot of S670ds were sold. i have a welder that has welded some front cases for me & guarantees his work. Never had a return. Can't say if it is repairable till seeing it. Email me if interested

email me for ordering info.

I think your problem is ring/pinion. I think if you had one wheel on the ground & one jacked up & both jacked up wheels turned without resistance that it wouldn't be in the final drives. I do have used FWD parts.

I can supply a M2801fd parts book

Those are all Iseki #s. It is not used on Case or Cub tractors.

I can supply a good head.

I can probably supply you with a block heater. Email me if interested

The MT21 ring gear was not used on any US models.It wasn't a common import. I doubt it is still available from Japan. Good luck. I do buy parts tractors.

It helps to tell what model you have.

i can supply Iseki parts. Email me for details

I install block heaters. They are the most efficient way to heat the engine.

Yes I can supply the plates & spacers. Email me.

There is a ball with a spring to keep the lever in the position you want it. It may be froze. If this is the problem, Tap the lever lightly either way to get it loose,

email me. I can probably supply the parts.

What size are your rear wheels?

Control valves are usually not rebuildable. There aren't orings , just close tolerances.Any open center valve with the correct flow rate will work. Might take some hose adapters.

You don't need to get the OEM Bulldog valve. A US made valve is probably a lot better. I have two lever or joystick valves for compacts.

I can supply parts to rebuild I also have a good YM4220 motor.

I installed mostly freeze plug heaters in compact tractors. If they won't work I use a lower radiator hose heater.

We are repairing 2wd front spindles. The pictured spindle is for a D2350. This is a new axle shaft with tapered roller bearings, seal, wheel hub, axle nut, cap, & bolts. This is not a welded broken axle shaft. If you have a broken axle contact me at parts@sheaftractor.net.

We are repairing 2wd front spindles. The pictured spindle is for a D2350. This is a new axle shaft with tapered roller bearings, seal, wheel hub, axle nut, cap, & bolts. This is not a welded broken axle shaft. If you have a broken axle contact me at parts@sheaftractor.net.

ASAP bought out Hoye.

I can supply a flail mowers or a regular rotery cutter may also work for you at a cheaper cost.

i can supply the closest manuals & a parts book.

I have a used ym240 loader for sale Email me if interested

I have parts books & can supply parts for the Shibaura p21f. Email me.

The only similarity between the Iseki TX1300 & Satoh S370 is that they both have a KE70 engine. Rest of the tractor has different parts.

I can supply the closest manuals & MTE2000 parts book.

I can supply axle parts. Email me

email me for manuals or parts.

It is metric threads.

The OEM filter is not available. The replacement filter is expensive.

I have new & used S370d parts.Email me for details

no

Shibaura does/did not supply Chamber inserts separately. I've been through this problem before.

No one is producing a replacement to my knowledge.

i CAN SUPPLY THE #27 FILTER. THE # 18 is discontinued. In place of #18 i supply an external spin on filter.

I have available A tu SERIES OWNER'S MANUAL

Some of thesmaller Iseki tillers were 2 point tillers instead of 3 point.

DID YOU SEND TO MY EMAIL?

i MAY HAVE A GOOD USED STEERING WHEEL. iF i DON'T i CAN SUPPLY A REPLACEMENT WHEEL. EMAIL ME. PROBABLY CAN ALSO SUPPLY THE HOSE.

THE BUCK HAD 6-18.THE S373 HAD 6-16. THE TRACTORS WERE THE SAME OTHER THAN HAVING A DIFFERENT ENGINE.

The posted parts book is very small print. It looks like there is a serial # break. The TX2160 was sold in the US as a Bolens G174 3 cylinder model. they all used the 27 setup. The 2 cylinder was also sold as a G174/TX1500f

I've used Sodium Silicate for years. I used it on a Ford truck gas engine & a Kubota excavator with leaking head gaskets. It worked on both of them. I had a Pontiac quad four engine with block crack i used it on. Every time I stepped on it a little it would start leaking. I don't have much...

I don't think a sealing product will work on a hole in the block. i had a 6 cylinder ford engine that got a pin hole & sleeved it to fix it. I do have a used block or short block available or possibly could supply a complete engine.

If you cover them for a long period you need to use a white cover. I'd recommend buying some bale sleeves. they can be reused. I store around 250 6x6 bales inside but I also use some sleeves to store extra hay close to where I'm feeding

They would fit. Usually the rim width is an inch narrower than the tire size.

27 is what is on a 3 cylinder model. 18 is what is used on a 2 cylinder model. I haven't seen a parts book that covers both 2 & 3 cylinder models.

I can supply you with manuals, email me.

yes. Just different bores.

engine oil capacity-1.06 gallons

It would work on a MT180, If you have both tractors you should be able to take some measurements to determine if it would work.

I can supply you with one. email me

what tractor model?

I can supply your filter

I ship internationally by post since 1997. Hasn't been a problem.

Have you received a seal that fits without the 2 small tabs

email me

If there is no screen there is a good possibility the pump is shot. I usually supply an external screw on filter in these situations. I may have a used pump or can supply a new one.

What parts do you need? I have parted out 3 of them & also have some new parts.

I've parted one out. I'll have to check if I have that part. Are you looking for the housing the axle shaft goes through?

I have YM1510 parts tractor email me

Email me for manuals.

I may have a good radiator

This is engine hp. The 24 may be pto hp. I have never seen a fuel gauge on the tank of a S650

Could be over filled or a plugged breather tube.

It is a transmission driven pto. It is operating normally. You need an overrunning clutch.

Best thing to do would be to check the pressure. Put a tee in one of the loader lines & run it to the end of the cylinder stroke & check pressure. Should be around 2000 psi at full throttle.

Have carbs available.

I can supply the closest service manual but a parts book may be more useful.

I might have a dipstick.

Nothing would have the same frame dimensions. The 1500 is larger than the YM1300 & smaller than the YM2000

I do have some Yanmar tractors I'm parting out.

I can supply it. Dominion is no longer a Yanmar dealer.

Did you run the tractor with the lines unhooked? If so there is a key on the hydraulic pump shaft that will shear because the pump is dead headed. I had a customer bring me a tractor that the Deere dealer had for a month & couldn't figure out what was wrong. Before he unloaded it from the...

Last time i checked with hoye's supplier they were out of stock & had no one to make them. I fabricate wheels that are discontinued. Won't look exactly like the OEM but will function the same.

The I&T shop manual would not be a good one for the D2500. It was an earlier 2 cylinder model. The R2500 has the same engine series which usually I recommend the closest engine series.

I've unstock clutches running a mower on the back. I've also unstuck them by running them & hitting the brakes, but the problem withthat method you can also break something in the transmission.

I have bought parts from Ag Meier as a dealer, but can't confirm what belts they are.

I might have the shaft but doubt I have a complete final drive hub

You probably sheared the brake pinion shaft. I've done this on a JD2030 & a YM1610

What is the part #?

All I can supply is a parts book, but it doesn't sjow a breakdown of the valve. This tractor has no compareable US model.

I have a used one. Email me.

What parts do you need?

You are probably referring to Bill Rogers at Valley Power. He passed away in January & the business is closing.

yes

The only thing available were parts books. I used to keep all the parts books but it was so hard getting parts from Japan & there were so many models I gave up. Every model tractor had multiple models of tiller. I can supply tines, bearings , & seals.

The MT4201 is a Japanese model. I can supply the closest US model manuals.

email is parts@sheaftractor.net

That's good. A customer had a MT180HD that had the front pump. The drive was like a real thick cable. It had a tendency to rust & break. I replaced it once, but the second time it broke it wasn't available. I had fits trying to find a coupler that would fit in there & hold up.

They are standard size hoses. Hydraulic seal are pretty universal. I had a Japanese loader that needed seals . I was able to find them.

If you don't have a clutch alignment tool, center the dick in the pressure plate. I've done this many times.

the only English operator or repair manuals are for the Fords, I can supply the closest manuals & Japanese/English parts books

We rebuild steering boxes. You probably had a lower bearing go out to start with. What is wrong now is that the ball/nut assembly on the steering shaft has come apart. Depending on the condition of the shaft you may need the whole steering shaft assembly.

They are a good loader. Does yours have a front pump?

Sounds like a practical solution.

I can supply some new parts & am parting out 3 of TS1610/1910 tractors

It least it was an easy fix. Sometimes the most obvious is over looked. i had a customers fairly new tractor that the clutch was slipping . It had worked before setting for 6 months. I split it & the clutch disc was fine but replaced it. Put it back together. Still slipped . Got a shop manual...

I can supply manuals

I can supply manuals email me if interested

If you are getting air in the steering look for a small leak in the hoses. Did you fill the filter housing with oil? Crack the pressure line at the pump. This will keep from any pressure building up.

I've always split the tractor to replace a clutch. There is a lot less to remove than pulling the motor. Put blocks between the engine frame & front axle so it doesn't tip. Block the front & use a floor jack to move the back half,

Schwartz is no longer in business.

It is a Japanese model tractor. The MT21 parts manual I have is in English & Japanese. Operator & service manuals would be for the closest US model, Email me if you need manuals or parts.

You need to find a loader a little wider than your tractor. If you let me know the width i can see if I have one that would fit.

I wouldn't be to concerned if it only comes on when hot & at idle as long as you weren't trying to work it at idle. If it had low pressure at high RPMs I'd be concerned.

The first thing to do in a not starting problem is to bleed the fuel system. Start at the tank & work to injector pump. Open bleed screws on filter & injector pump & close once fuel without bubbles comes out. It doesn't matter what the temperature is , it needs the glow plugs to work. The glow...

Either a rod is disconnected or the pressure plate is shot. You'll need to split the tractor. I can supply parts.

I doubt any one makes brackets for the D2500. You'll probably have to find the right size loader & fabricate brackets.

I don't get on the forums as much as I used to. Still dealing in parts & whole goods. My Yanmar business really dropped when Hoye started their website, Plus Yanmar's lawyer kept threatening to sue me if I mentioned Yanmar on my website even though I had the Yanmar disclaimer that other websites...

the website was on my post. www.farmpartstore.com is my commerce sight but I have many more items available from other suppiers.

I can supply a starter or a solenoid

Any numbers on the alternator?

I can supply you with a hydraulic top link & I think I can have it drop shipped from a warehouse in Canada. I ship from the US to Canada but it would be cheaper shipping from Canada plus no custom charges.

i can supply the seal.

I would say it got cleaned up and the pressure is normal now. I have tractor that runs at 100 psi when reved up. I wouldn't worry about high oil pressure.

I had a SP1740 with a loader. Koyker made a lewder for them. The SP1740 is 4wd. If you get a loader don't get very aggressive with it. The one I had the person I bought it from had just purchased it with a new loader. When he brought it home the 4WD quit. They don't have a very stron 2wd system.

you didn't mention if the glow plugs work. This engine needs to be glow plugged to start.

You should be able to get $1500. maybe more . I make reversers for the S370. They run $900 new. I have parted out around 10 s370 tractors. I've sold a couple motors in the last 20 years. Other parts on a 2wd go real slow. FWD parts are the most in demand parts, but it has slowed down the last...

The reason they had a short shaft is that they didn't use a three point hitch. They were attached with a 2 point system. If you are using a 3 point you will need a longer shaft that extends. I can supply adpters & shafts.

There are alot of S650 tractors running yet. It was the Japanese tractor widely marketed in the US. I have over 10 S650 parts tractor on my lot. I also have a used loader & a powersteering kit. Engine overhaul parts are getting scarce.

I never saw where you bled the fuel system. The pump can not pump air. Start at the tank & open each bleeder screw enough to let air out, then close . There should be two on the fuel bowl & one on the injector pump. I get many calls for people trhat think they need an injector pump when all they...

I would suspect the pressure plate is bad. The diaphragm is not being released. The tractor will need to be split to replace the pressure plate.We can supply parts

This has always been an issue with the Japanese tractors. I heard that the Japanese had a different oil rating system but the US model parts books recommend 80-90w. No US farm tractor since the 50's has recommended 80-90w. Yanmar recommenced JD303 or better which today is probably any hydraulic...

I can supply the pto clutch plates

My first thought on the oil light is the sending unit is bad. I've run across this often on tractors I imported from Japan.

i WILL

2wd

I've parted out 3 of them, but guess I sold 2 of them. I know I had one with the creep, but the one I have left doesn't have it.

Yes The GLF models have the creep.

It doesn't have a screen. Just the filter. Valley Power is closing, Bill Rogers the owner passed away.

Iseki was good at giving multiple designations. The TX1704/g174/2160 was a gear drive. The H174/H1704 was a hydro. I have manuals for both models. I can supply engine, clutch & most fwd parts. Transmission parts some are available. Can't tell which until someone inquires about them. .

I have manuals for most Iseki tractors.

I have parted out a TS1610f. I'll have to check if it has the correct clutch housing. The were 2 styles for the TS1610f. Some had a creeper gear in them.

I can supply you with parts. Email me at parts@sheaftractor.net

The parts book shows a filter on the suction line in front of the steering column

It could be the lift cylinder is leaking & when it it gets low enough it lifts.

It has a Mazda PB1000. You probably will need a different carb. The accelerator pump leathers are probably shot & it is common for the tapered chamber to get pitted when not used. I have rebuilt used & new Nikki carbs

I have used springs . would have to check new are available.

You can move it around without causing any damage.

yes Email me at parts@sheaftractor.net

Thank you

I have a lot S650 parts. I have around 10 S650 parts tractors

Email me at parts@sheaftractor.net

Just replacing the seal will not fix the problem. The internal seals are bad. It is not a repairable pump. If you supply the numbers off of the end of the pump, i can probably supply you with a new or used pump.

If it is a Nikki carb, it is for an electric choke. You don't need to connect the wire. You have a manual choke. I probably sold him the carb I was able to find several new ones.

I usually cut the pressure line & braze pipe fittings on the cut ends, Bell adapters work good. You can drill the line side to the size you need. Run the pump side to the IN on the valve & the OUT to the other cut line.

i have available various length sway chains w/turnbuckle. Fairly reasonable.

The Bison has a PB1000 gas engine.

Did the shops you took it to specialize in head repair?

Don't know if new are available. I should have a used one.

If the lever doesn't move at all, it is probably froze where it goes through the housing. Spray nut loosener on it & tap gently. It should eventually move a little. then keep working it back & forth.

Sd1540 or SL1540? I have parts tractor of both models or can supply aftermarket

There is a fuel filter in the banjo fitting where the line attaches to the card. Other common carb problem is bad accelerator pump. The S650 is not gravity fed & has a fuel pump. the fuel system is not pressure regulated

Most control valves spools are machine fit without orings

Do you need a new pump ? As old as that is I'd be surprised if that particular pump is available. My pump supplier may know what it is & can probably supply a compareable pump.

I would first check the hydraulic pressure. Does it jerk as it is going up?

I can supply new & used S650 parts

KI still have the loader. Dixon IL 61021

I can supply parts for the TS1610 including fwd seals.

I parted out a K4D. Basically the same tractor. FWD gears that go bad are all ready gone

I can supply you with Yanmar parts

I have a farm & use tools hard . I was buying tools from Harbor Freight when they were only mail order. the quality of wrenches has improved a lot. I used to buy them to put a set in every tractor. I'd rather loose a cheap wrench than an expensive one. I've bought quite a few of the 4-1/2'...

looking for salvage or broken tractors

I can supply you parts from the USA. Email me at parts at sheaftractor.net Je peux vous fournir des pièces depuis les USA. Envoyez-moi un e-mail à parts at sheaftractor.net

Most Japanese tractors were used mainly for rototilling on small plots. Tractors with loaders usually were on livestock farms.

the Suzue M2001 has the K3D engine. What is the pto shaft like?

There is an internal spring. If it hasn't been used for a while, spray a nut loosener on the shaft where it enters the housing. Probably rusted.

I may have carrier and can supply associated bearings. no to front ring, pinion,

I'm a Sparex dealer . They don't have ring/pinions. The part is discontinued. About the only option is to have one made. Very expensive.

Most Japanese tractors did not come with loaders. It could be a Japanese, Vietnamese or a US loader.

If you can't ge tit loose saw the nut

It is discontinued. Can't find any used. I've priced having them made. Very expensive

I have a TU operator's manual availabial

I can supply you a parts book & closest service & owners manual. Also parts. Email me at parts at sheaftractor.net for manuals

I imported tractors & parts from Japan. I was never able to get a service manual from Japan.I recommended people to get the parts book so you have the breakdown & part #s for their manual. Them get the closest US service manual which is the YM169. I usually look at the parts book before the...

I don't read Japanese. From the parts book it looks like what I think is the 2 speed is electrically activated. I have an RX302 which looks like the same setup as the RX301. Email me at parts at sheaftractor.net for manuals

the 2 speed is a pedal on the floor. I can supply a parts book.

You don't want to dead head a pump. Dead heading is when the pressure line is blocked. If you disconnected the the loader hoses & they had snap couplers that you did not connect together & ran the tractor the oil from the pump would build up tremendous pressure & damage the pump. There are not...

i CAN SUPPLY YOU A YOKE ASSEMBLY & TIE ROD ENDS. eMAIL ME AT PARTS@SHEAFTRACTOR.NET

DO YOU NEED THE FUEL LIFT PUMP OR THE INJECTOR PUMP?

EMAIL ME AT PARTS AT SHEAFTRACTOR.NET

It was either overfilled or it has water in it.

Did you sell the tractor? I would be interested if you still have it.

I have one but it will need to be rebuilt

I can supply you with seals. The axle has to be removed to replace the seal. You have to remove the lift housing to access the circlip that holds the axle in.

deereman75 GAVE THE BEST RESPONSE. iF YOU HAVE TUBES $ CHLORIDE IS LEAKING, GET THE TUBE REPAIRED RIGHT AWAY. Rims RUST OUT WHEN THE OWNER WAITS TO GET IT REPAIRED. MOST OF MY TRACTORS HAVE CHLORIDE. MY jd2030 IS TUBELESS & THE RIMS HAVEN'T RUSTED.

I make these. I have centers plasma cut & use new rims.

Did you dead head the pump?

Agco should have a service manual for it. I can supply parts

I believe I sent you an email with pricing for under $1000. If you do decide to sell the tractor as is, I'm always interested in parts tractors.

The design used on the TU series was not used on US models. The closest would have the same engine series. Massey 1240 or 1125

I may have a used pump.

I don't like to do pricing on message boards. I sent you a private message.

Rebuilt or new are available. email me at parts at sheaftractor.net

Cut the pressure line, attach IN on valve to pump side OUT to rear end of lne.

I can supply injectors. There is a serial # break. You can email me