Search results

Hey Zwelch - if you're still out there - want to hear updates on your Sany. I have a 2016 Sany sy35U exc with about 1000 hours on it. It's been a very good machine. I'm surprised there aren't more threads about Sany excavators on TractorByNet..... vg

Hi - I have a 2016 Sany SY35 excavator with 350 hours. I bought it used a year ago. It is a 8500lb machine. The Boom deflection cylinder does not work. This cylinder pivots the boom at up to 90 degrees either direction from the cab so you can dig close to buildings, etc. It is operated by a...

Looking at upgrading the loader on my 2210D. It's sort of a home made design that are very common here in the NW. It works fine but is a little light duty and much has to be greased manually (no zerks on most). So I'm thinking of buying a YM240 and swapping loaders. Does anyone know if this...

I need to replace my rear tires as they are splitting apart between the paddles, and innetube is showing. I'm wondering who has done this and what tires did you buy? My front tires are new (couple years ago), so I'm going to have to figure out my rolling circumfrence so I keep the correct lead...

Anyone know where I can get a replacement lift arm? I somehow bent mine! Left side - this is the arm that attaches to the splined shaft that comes out of the 3-pt. lift casing. I know new ones are available, but I was hoping to spend less than $100.....alot less. I haven't had any luck so...

My Battery charger seems to be on the fritz - it's an older 10amp that seems to kick off via it's built in circut breaker on the last 3-4 batteries I've charged. one was completely dead and another was close so I thought that was the cause. But it just did it on my tractor battery and it was...

I'm rebuilding the front end on my YM2210D after the top bearing on the vertical drive/steering shaft rusted apart and fell down into the bevel gears and bunged them up. Finally got some used gears and new seals/bearings but a closer look at the top of this shaft and the bevel gear housing...

Tractor - 2210D - has been getting harder to start.... Had water in fuel....cleaned tank, still had water in my fuel bowl couple days later - cleaned it out. Still hard to start - starts on one cylinder - then the other will kick in, but would run fine then....was thinking bad ring or bad...

Tractor has been tough to start lately - and once it does start to fire it sounds like only one cylinder is firing and then you hear the other one kick in after a few seconds...motor then starts to run smooth, etc. I suppose i need to check the injectors and possibly compression? Any...

I bought a new 5 foot box blade for my 2210D Yanmar - the lable says "5 Point by King Kutter". It's painted dark brown and has a fixed top link mount (not bolt-on), 4 rippers, seems like a decent unit. But I've never heard of the "5 Point" name - anyone know?? thanks

I'm going to have a ROPS made for my 2210D. I was wondering if any of you could post some good pictures and or diagrams of ROPS for similar tractors so I can show the guy whos gonna fabricate one for me. Maybe it wouldbe best to buy the mounting brackets from Yanmar and have the rest made...

Anyone have a source of lug nuts for the rear wheels on my 2210D? I need 5!! or mcmg@lclink.com thanks, mike

Think I've found the screen - but I can't get the cover plate off. Is it 3 screws facing the left side (if sitting on ractor)? I could not free this cover from the transmission. It is on the opposite side if the trasmission from a hydraulic line - when I took off this line I could look into a...

Do I need a puller to remove the steering wheel? I'm drilling holes on my dash for guages and the wheel is in the way... thanks

Looking at installing water temp and oil pressure guages. Looked at old posts here and the yahoo site. One questions still lingers - for the temp sender - can I install a metric adapter and then a "T" for my guage sender and one for my dummy light? Or does the sender have to be in the block -...

I have end play at the main pivot pin in the the front axle housing of my 2210D. The manual says it should be less than 0.02" of end play, but i have about 0.2". I discovereded it when attempting to turn the steering wheel while the tractor was off - the pumpkin would bump front and back...

Anyone know what type of u-joint I should order for my tiller PTO? I see Agri supply sells series 1-8. How do I tell which one I have? I have a 2210D with a RS1400 (yamnar) tiller. Obvious novice at u-joints - the last one I messed with was on a 1973 pontiac station wagon.... thanks!

I've got my front end apart to replace oil seals. I've got the gear housing with axel off the tractor and I'm wondering a couple things - should there be ANY play in the drive axle end? I can move the axle in and out a little - 1/4" or so... The other thing is the 80w-90 front end oil looked...

I'm curious how people skid logs with their tractor? Has anyone made a gizmo that would allow you to back up to a log, lower the 3pt and with tongs or something, grab the end of the log lift it up and skid away? Or an arch - a 2 wheeled trailer that actually lifts up one end of the log as you...

I'm considering building (having someone with real welding skills build it) a ROPS for my 2210D. What would be nice is to use an existing ROPS as a pattern. In the unlikely event that anyone near me has a compatible ROPS -- Does anyone have good pictures or diagrams of ROPS for their tractor...