I was looking at the parts explosion of a dual 2nd scv for the FEL on my 4100. There is a plate between the valve itself and the rear housing. The plate has two plugs on it, one at each end. Are these plugs pressure and and suction or are they controlled by the valve and thus would operate only...
After a few hundred hours, my 410 FEL finally has a leakdown in one of the lift hyd cylinders. The bucket will drop pretty quickly with a load in it and does make a weird sound in one of the lift cylinders when being raised. I guess its time to overhaul the bad cylinder. Would it be wise to do...
I\'ll never complain about JD\'s parts prices again
I just had to order a gas tank for my pressure washer with a 6.5 HP Honda engine. The tank was $120 for a 1.something gallon tank. Unfortunatley I had to have it, the old tank had several rust holes in it and I could not repair it. The tank...
Anyone got an idea what a 1990 750 4wd with FEL is worth? It has low hours, about 400-500, garage kept, really good shape. Also a few attachments are available, rear mower, post hole digger, blade
Anyone have to replace the injection molded plastic boot for the power vacuum system on their 60" MMM yet? I had to order one the other day from the local JD dealer. I almost fell off the stool when I picked it up at the parts counter, $78.00 tax incl. Actually its not considered a part but...
Last week I did about 8 hrs of heavy FEL work with my 4100 HST and all was fine. I had it off for a few days and reinstalled it to again do some moving of gravel. It was then that I would hear a popping or light clunking sound from the front of the tractor when I had a full bucket and was...
As most everyone did, I changed the hyd oil in my 4100 to the newer low viscosity oil from JD. I noticed that the lifting power has diminished on the FEL and this coincided with the change in hyd oil. Has anyone else noticed this and how much of a hassle is it to boost the output of the pump...
I have noticed recently that my FEL on my 4100 JD does not seem to have the lifting power it used to have. Its over 1 year old, I think its out of warranty. any thoughts on how to do a quick check without guages and all that?
I noticed the last time I used my 4100 HST with the FEL, the power steering was a little sluggish, problem went away when there was no load on it. I think I might have a Hyd. pressure problem. Just changed the hyd oil the other day so will try it again tomorrow. anyone have this problem?
I have read a few posts about people finding shavings in the hst trans when changing hyd oil. I serviced my 4100 the other day for the first time and the screen was for all intents and purposes, clean. Of course there was only 50 hours on the tractor but I could not stand it any longer , had to...
For all those that use their 4100 or up with HST to bush hog in heavy brush, be aware that the safety (deadman) switch on the trans is at the bottom of the trans and easily pulled off in heavy brush. I found that out the hard way after an hour of trying to get the @#%#@@@ thing going a 1/2 mile...
Well the grass is mowed,the garden is watered and the JD is all tucked away. I am going fishing off-shore if the wind stays down or maybe clamming if its too windy........
A local organization that I belong to recently had a demo-derby. One of the members brought his 34 hp Kubota with a front loader and box blade to level the track and move crashed cars. Anyways, in speaking with him about how he liked the tractor( it was several years old) he commenced to tell me...
I have a 4100 HST and plan on getting a box blade to do about 1/2 mile of dirt road. I have r-4 tires. Is a 4' blade too small and too light? I have heard that you should go a few inches wider than your tires. Mine are about 47" wide.
I have an old(20Yrs) 210 with two decks, bagger, tiller and hitch I want to sell but have no idea what to ask. I consider it average condition. Any ideas??