Does anyone have access to a PDF of the service manual for a Ford 1200 tractor?

I just purchased a 1980 Ford model 1200 tractor with a Ford 768A loader. I would like to change the hydraulic oil and filter but I can't find a part number for the filter. Hate to put new oil in...

looking for LH Steering arm and hydraulic parts for a Ford 1200 4x4 diesal

Hi all, I took my front differential apart and found a broken tooth on the pinion gear but the ring gear looks OK. Can I change out the pinion gear and use the same ring gear or does it have to be...

Hi everyone, I broke my front diff on my 1980 ford 1200. Does anyone know were I can fine a replacement or the internal parts? Thanks, Ken

My 1983 Ford 1200 (4 x 4, 2 cylinder model) has a front-end loader and a counterweight on the rear 3-point linkage. With the quadrant control in the locked upper position (continuous pumping)...

Because I cant do anything right the first time I have to split the tractor again. Of course I put new oil in it. Is there any way to do this without draining all the oil back out?

Does anybody know how to change and or fill the oil in the front differential of this machine? I dont want to spend the 50 bucks for an owners manual. I have a sort of shop manual and it shows...

is their oil in the front differential and if their is how do I check and change it?

I have a 1200 I just split to replace clutch. The old disc looks worn but not that bad. Should I replace the throw out bearing and the pressure plate? The throw out bearing wont come out...

Anybody give me the readers digest version of how to get to the clutch? I have a manual from the internet and its terrible!! I have done car clutches before so I am pretty good backyard guy...

Hi all, Just bought a nice used little 1980 Ford 1200 tractor. I have two questions on the mwfd.One can you engage with the tractor moving as long as you are not spinning? Is it alright to let...

Hi all, new to the forum:) I have a 1981 1200 Ford 4x4 tractor. It has a 16 HP diesel motor. It is a great little workhorse, but lately I have started having issues with it stalling, mainly going...

I'm going to try swinging by this estate auction on Sat (it's very close) and couldn't help but notice how clean the Ford 1200 (second picture down) looks. I don't really need it, but if it's a...

Hello all, I'm looking at a Ford 1200 with 4wd with FEL and 3 pt mower. It seems to run well and has new rear tires. The price is $2400.00. It has about 1100 hours on it. Not looking for...

Where is the Central (Diff Housing) Oil Filler Plug? (and the Level Plug, if they are not the same) - can't find it in the Parts Book.

Recent purchase - complete with Front End Loader - Have checked all oils etc except - can't find the Bung and/or check plug for the front Differential - can anyone help? I have the Shop Manual...

can someone tell me if a 768A loader will fit the 1200? or what the difference might be between the 768 and 768A? thanks

Hi I'm looking for a 75mm piston for a 20+ year old Ford 1200. It has a Shubaru engine. Other details sent if you have one. I'm in New Zealand and have been looking for over 12 months...

Hi I'm looking for a 75mm piston for a 20+ year old Ford 1200. It has a Shubaru engine. Other details sent if you have one. I'm in New Zealand and have been looking for over 12 months...

I am looking to get a set of Turf tires on a seperate set of rims, currently have R1's on. Just wondering what other rims may fit ( 1210, 1220 ? ) keeping in mind the tire ratio as the tractor is...

I need to replace the radiator (I'm told the original is unrepairable) and cannot find an aftermarket unit. I've contacted several F/NH dealers and have gotten conflicting answers on the...

I have a Ford 1200 (model year 1980) and understand it was built by Shibaura. Would anyone know what the model designation would be in the Shibaura line? I need to replace the radiator and F/NH...

I have access to a nice Ford 1200 other than the fact the engine needs a crankshaft. Nice factory loader, rear axle, front drive axle, wheels, sheet metal, transmission, 3 point. Would take...

Hi I am looking at a Ford 1200 4x4 with a FEL, year is 1984? has under 700 hours with a 2 cylinder diesel and has PS. Just wondering what others have experienced or what problems can be expected...

i have a ford 1200. early 80's model. i have a cracked crankshaft, and i havent been able to find a new one. its a 2cyl. its impossible to find parts for it. any one know of a motor i can replace...

Anyone know about a FORD 1200. Is it a decent tractor. I found one with 60' belly and rear grooming mower, snow blower for 2,600. is that a good price? Diesel, 4wd, 16hp

buynh-ML-874061-ML- New Holland (Ford) specific post

I have a Ford 1200 tractor. Lately the lift arms have been creeping up on their own. It seems like it might be related to cold weather, but I'm not sure about that. In a few minutes the arms will...

I'm looking for general information and experiences with the little 1200. So far I believe it's a 16 hp 4x4, 2cyl diesel, 5 forward and 1 reverse spd with high and low. It's rated 13 hp at rear...

Looking at a Ford 1200 4wd; wondering if anyone has any info - I know the HP and weight, etc - wondering about lift capacity, parts avail, etc. Also found a Ford 1100 - seems the 1100 is slightly...

I am looking at a Ford 1200 4wd, would like to know what Shib model this lines up with. Frankly, I can find more technical detail on the web about a grey Shib than an old Ford. Thanks

Hello and a pre thanks for any help. I am searching frantically for a crank for the above said tractor. The tracor # IS U200919 And Engine # IS lek802d-206659. My friend has about given up...