Looking for a first tractor and stumbled across a 1996 Nortrac 304 with 579 hours and a Great Bend 240 FL for $6500. What's the consensus on these? I'll be using this for a 12 acre homestead...

I have a 2005 jinma 304. It seems that i have a single stage clutch withought realy knowing what i am looking at but all the manuals and instructionals i have found show the Access panel on the...

Dose the pto on my 304 work via the clutch at all. When cutting hay i have to engage the pto and then start the engine With everything running. Is this korrekt or am i missing something?

I'm new to tractors, but I found a farmpro 2340 with a loader, backhoe and low hours. The backhoe is still attached, but I was reviewing the manual and getting acquainted with it. I attempted to...

Hi all, I need some guidance on an issue with my tractor. I went out to day to start it up and move it, and it barely started, running on what seemed to be only one cylinder and was pouring out...

My 304 has had low pressure when idling for a couple of weeks. When mowing of tilling at full RPM's the tractor was more or less fine. When I left idling the pressure would drop fairly low and the...

The price of the JINMA 304 seems very good. Anyone have experience with a Jinma 304 and/or JOSEF tractor?

I have a Jinma 304 and I have air in my front loader hydraulic line.....how can I bleed it off? Illarion on Vancouver Island

hi all:):confused2:

A couple of days ago I was doing some brush hog work in the upper mango orchard and I noticed that my front end seemed a bit loose. That is, the steering was sloppy and that made me more than just...

I was moving a bunch of trees and brush today and after a couple of hours I noticed the gauges had all quit working. I checked and the fuse for the voltage regulator was blown so I replaced, but...

Are there any tricks to putting a watterpump on this tractor that I should know about?

I've got a 2003 Jinma 304, with 430 hours on it. The oil pressure gauge has always registered just above the red zone, but yesterday it started straddling the red zone on the factory gauge. Any...

Howdy guys, Well, I found out about a month ago I am going to be a Daddy, got my first one on the way. So I got to get rid of some things. I need to sell my tractor. It is a Jinma 304 4x4 (no...

Hello All, Does anyone know of a NAPA part number for a Jinma 304 Air filter element. I checked mine the other day and shook out lots of stuff, figured I better buy a new one as the old one is now...

Hello guys, I am looking at a 2006 Jinma 304 with 60 hours, 6ft hawse bushog, and box blade. The tractor looks just like new. He said it has been excellent and had to do nothing to it. He says he...

Hello All, I am trying to get my clutch adjusted on my Jinma 304 and can mostly find procedures for the 354, WHAT exactly are the differences? Thanks in advance, Rick

I have a Jinma 304 with a Koyker 160 loader, with a bale spear that attaches to the bucket. Periodically, I need to move round bales for our horses. I don't have difficulty picking up smaller...

Can\'t Engage 4WD on Jinma 304 After using 4wd last weekend while turning my compost pile, I shifted back into 2wd. Now I can get it to return to 4wd, the lever moves a little but not all the...

Crossover Filter #\'s for Jinma 304? I understand that a NAPA Gold 1515 may work for the oil filter, does anyone have a crossover for the fuel filter for the 3 cylinder engine in the 304? As an...

Hello All, I just sold my Ford 650 and told the buyer that I would let him have my 60 in ch box blade. I sold the Ford because now I am sure the Jinma does the job of the Ford, plus much more. I...

Hello All Again, I had my tractor out again this Weekend and parked it for lunch with the right side of the tractor lower than the left side, maybe 6 to 10" lower, anyhow, when I got back from...

Well spring is almost here in Mass. so I went out to my daughters land to start getting things ready. My tractor has been sitting there idle since December so I figured the chinese batteries...

Jinma 304 Won\'t rev!! Hello All, I was out on the tractor yesterday, I now have 47 Hours on her without issue, and I noticed I cannot get the RPM's past 1800, could this simply be a linkage...

Hello All, My dealer did not install my seat belts on my Jinma 304 and said he would never use them if he were me, however, I would like to install them anyway and use them, but cannot figure how...

I'm looking for an inexpensive subframe backhoe for occasional use on my Jinma 304 equipped with a Koyker 160 loader. Anybody have one, thoughts on price?

When the temperature dips below the mid 30's, my Jinma 304 will frequently spin the starter but not actually rotate the engine with the turn of the key. I have a 2004 with the non-epa engine...

Hello All once again, Well I was just talked into changing all of my fluids on this board on my last post. Is their filter part numbers cross reference to ,say, a NAPA part number, where should I...

Hello All, I am new to the Chinese forums and just yesterday bought a Jinma 304. I am having some issues and hope you all mmight be of some help 1. The FEL, which is a Japanese unit, I think the...

My new Jinma 304 seems to run cool under all conditions. Last week the temperature here was 60 plus degrees while I was moving gravel, the temp gauge never went above 50 degrees. Anybody else...

I've got 10 hours on my new Jinma now, and wanted to pass along some of my initial impressions. First, the 304 has plenty of power and it is a larger compact tractor. I could have easily made...

Hi everyone. I am new here and trying to educate myself about the Chinese made tractors. I was looking at a Jinma 304 4wd, with Koyker FEL and a Box Scraper being sold by a private party. He...