Recent content by 07keo02

  1. 0

    GC1705 CRI grapple installed

    Sorry for the late reply, just under 200lbs.
  2. 0

    GC1705 CRI grapple installed

    Finally got my Cold Roll Industrial grapple installed on my GC1705. Not much seat time yet but a sneak peak of what it has accomplished in a short amount of time.
  3. 0

    SAE 8 orange boss leaks

    If the o-ring is squeezing out and showing then either: 1: There is no counter-bore and in this case the port is not ORB. 2: There is insufficient shoulder on the fitting. This could happen in a swivel 90 where the nut/washer was removed and the o-ring was installed against the hex portion of...
  4. 0

    GC1705 Project-additional hydraulics

    You dont have to remove the tank. You just have to remove seat, rops, grips and rear fender assy. I did put a 3/8 bspp to 3/8 jic adapter there and ran a new hose, but It would be easier to just series into it underneath the tractor where it goes from hard to soft line. This is especially true...
  5. 0

    GC1705 Project-additional hydraulics

    Hard to see but that fitting back there is where the PB soft line terminates. I removed it completely because mine now runs from my top link valve to this spot.
  6. 0

    GC1705 Project-additional hydraulics

    No it is not. Pretty sure thats the tank line from FEL valve. The PB line is the soft line i showed earlier in the thread that terminates underneath the front of fuel tank. Basically impossible to get to without removing the rops/fenders. You can just tap into each line underneath the tractor...
  7. 0

    GC1705 Project-additional hydraulics

    Been busy with other stuff but here is the final setup of the rear hydraulic top link. Hard to document now because i had a lot of hose modifications and experiments along the way. The basics are here, and taking off the rops etc is not absolutely necessary. Better to buy the basic setup and...
  8. 0

    CK2610 Hydraulic Remote

    How is your backhoe set up? When you remove it do you loop 2 hoses together?
  9. 0

    3 Point Hitch Only Raises When Curling Bucket Up

    Also, you could try: With all 4 quick connect lines disconnected from loader, hold your curl up function momentarily while trying to move 3 point. Only do this for a few seconds at a time. It should pop the relieve valve and send fluid down the tank line.
  10. 0

    3 Point Hitch Only Raises When Curling Bucket Up

    It is weird that it is specific to the curling function, unless when you are using the lift function there is no excess fluid in that moment to return to T line and supply fluid to 3 point. Need a better pic of FEL valve to identify PB sleeve instalation.
  11. 0

    GC1723EB hydraulic plumbing

    Mostly, but the FEL valve is completely relocated, which would obviously change hydraulic line routing.
  12. 0

    GC1723EB hydraulic plumbing

    Does anyone know the flow of the GC1723EB? I just got done adding front and rear remotes on my GC1705 but i still lack a backhoe. Its around 9k to add one, so I decided I'll be ordering a GC1723EB in the morning. I may just make a setup for the rear with the backhoe lines, but Im wanting to...
  13. 0

    3rd function valve kit

    I would recommended going with a summit universal 3rd function kit then all you will have to do is measure/have lines made and figure out where to mount the valve
  14. 0

    GC1705 Project-additional hydraulics

    I also added the SSQA last night. Just need to get a plate on the factory bucket to use it as such.
  15. 0

    GC1705 Project-additional hydraulics

    Thanks but I will stilly likely sell outright and get a 1725MB. Hydraulics are no problem but acquiring a backhoe and subframe for under 9k isn't likely. If i could get one for like 6-7k id just keep what i have and do it.
 
Top