Recent content by bxbuster

Bought a BX broom last summer and stored it outside. when I was attaching it to the tractor I noticed the section of the brush exposed to the sunlight had faded. The bristles had become brittle as a result. I just finished spring clena up on my yard and sure enough the damaged section is now...

For some reason my bx keeps shearing the roll pin in the front drive shaft. has anyone else had this problem or heard of such? I can't see how the pin is shearing as the shaft is splined. Thanks for any replies!

Sorry if this has been asked in the past but does someone have a part number for the quick disconnect fittings (male and female) for a bx? I'm starting a couple of projects and need the fittings and possible a t-fitting to t off the loader lines something like junkman has on his bucket grapple...

I originally posted this in the attachement discussions but thought maybe I should have posted it here so here goes: I recently acquired a John Deere Model 51 broom for my BX and was hoping to weld up a mount to mate to my quick attach and get sweeping. I was very disappointed to find the Deere...

I recently acquired a John Deere Model 51 broom for my BX and was hoping to weld up a mount to mate to my quick attach and get sweeping. I was very disappointed to find the Deere broom rotates the wrong direction . does anyone have knowledge on this model of broom that could offer some advice...

After a long search I stumbled across a rotary brush for the BX the issue is that the brush came off a Deere! I was hoping someone could supply me with a pic of the mounting bracket so I could adapt the deere brush to the Kubota quick attach. I already have the quick attach shoe so the hard...

The conversation about the BX fuel leak has gotten my attention. My warranty is up next month so I'd like to drop the tractor off at the dealer for any last minute issues. I'd like the fuel tank leak addressed if possible. I've already had the air filter update unless there is another one out...

I'm thinking hard about buying a post hole digger either online or from Tractor Supply. I'm sure this may have been discussed in the past but does anyone have ay recommendations? Will the BX2200 handle a 12" bit? Will there be horseposer limitations? I believe height is an issue but thought...

I have an older hydraulic turning blade that I have been using to move snow with great results. I was pushing back some banks under full power, I guess more like ramming them, anyway the cylinder no longer operates in one direction. I obviously know nothing about hydraulic cylinders so I was...

I was wondering if anyone had a BX Cab not mounted to their tractor that would be willing to give me some measurements or photos. I have a cozy cab from an old Bolens tractor, a welder, torch, saws etc so I can't see why this could be modified to work. I would rather not reinvent the wheel so...

I know I have read some posts a while back about height concerns with the bx and certain post hole diggers. With the 3-point modification to allow the 3 point to raise higher has anyone succesfully installed the post hole digger from TSC? They have an unbeatable price of 349 and only 99 bucks...

I already have both sets of tires but if anyone else is looking this seems like a steal... http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=41485&item=3838447223&rd=1&ssPageName=WDVW

BX Grass catcher on ebay and it\'s a steal! I already have this exact bagger and can't say enough about it. I think I paid close to 1500 for mine and this one looks close to new.... good luck! http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=46566&item=3825004788&rd=1

Unfortunately, I purchased a set of turf tires from a bx1500 off of ebay last night. This is unfortunate due to the fact that after I placed my bid I did the research and discovered the 1500 has smaller tires front and rear. The question is, will I be able to run the tires on my 2200 or will I...

What are your thoughts on an electric spreader that would hook up to the three point? I was looking at tow behind models and they run close to 200 bucks for a decent one. I really wanted something pto driven but that was cost prohibitive. I found this one on ebay and looks straight forward...