Recent content by cubowner

I need to replace my BX24 battery. Does anybody know what generic battery will replace / fit the BX24 tractor?

I started my work light project tonight. I installed a fuse block that will power all extras I add. I purchased two 1000 lumen led lights for the front and the Kubota rear work light kit for the rear. I also ran a 2 wire power connector so I can power my sander and sprayer.

Last winter I purchased a BX2750 blower that was in rough shape. Brackets bent bearings worn and paint chipping off. I used the blower last winter and now it's time for a complete rebuild. So I started the project this week so I can get my blower ready for winter. I stripped down my Kubota...

Today while working on my tractor I dropped a 1/2 rachet wrench on my dash panel and smashed the glass on the front of the instrament cluster. Now the fuel guage is not working properly and I have a big peice of of glass broken. I plan on replacing the instrament cluster but if I do my hour...

I need some guidance on rops ligth install. I purchased some rops light brackets from tractorcabdepot.com. Great brackets, but my dilema is how to mount. Should I mount the light on the outside of the rops or on the inside of the rops. If I add them to the outside of the rops it will add about 8...

My BX24 started to spray antifreeze around the top hose right above the thermostat. So I replaced the thermostat, hose, clamp and gasket. I thought I had it licked, I was using the machine today to do some snow removal and I started to smell that sweet smell when antifreeze hits hot exhaust. I...

Hey all I'm about to add some aux work lights to my bx24. I need some advice on where to put the switches for the lights. The dash is kind of crowded, any ideas or thoughts would be great.

Kubota BX2750 chute rotator and powered deflector Well today I finished my electric chute control. I built a custom bracket and mourned a power window motor for left to right control. I then installed a linuar aviator for up and down movement. Now to control the motors I built a handheld...

I was replacing my bearings on my bx2750 snow thrower and I noticed on the lower sprocket there was a bolt going throug the sprocket and shaft. I looked at the parts diagram and do not see that bolt. I bought the snow thrower used. I am wondering if that bolt is suppose to be there and if it is...

Well I started the second phase of my sprayer project. I added a 30 hose with reel. Next I'm going to work on the boom assembly.

I purchased a used 2750 snowthrower this year. I am wondering if anyone has a electronic version of the owners manual.

Has anyone ever installed a trailer plug on there bx24. I'm thinking of adding one but not sure if I should go with a 4 pin flat or a 7 pin. I would use it when I'm pulling my 2 trailers, also if I go with 7 pin I couild use it to power some rear mounted atachments. If anyone installed one on...

Well this weekend I decided to purchase a 15 gallon electric sprayer. Only one issue, I had no way to move it around. So I decided to build a 3 point hitch sprayer rack. I used some left over angle iron and welded it up and built a mini carryall for the sprayer. I hope to extend the hose to 25 -...

Well this weekend I decided to purchase a 15 gallon electric sprayer. Only one issue, I had no way to move it around. So I decided to build a 3 point hitch sprayer rack. I used some left over angle iron and welded it up and built a mini carryall for the sprayer. I hope to extend the hose to 25 -...

I was using my bx24 backhoe today to dig a trench when all of a sudden the hoe was making a squealing noise when moving the hoe from left to right and right to left. I shut the machine down and let it sit for a few and tried it again same noise. After about ten minutes the noise stopped but it...