Recent content by deminin

I have an 2002 Kubota 2910 that is showing a leak in the LH bucket cylinder. Looking up parts online, I found 2 "models" of this cylinder....B03002 and B03005....Both with the same PN of 7J045-64010. The model B03002 shows a seal kit PN 75545-64600 and the model B03005 seal kit is PN...

I lost a hitch pin on my tractor, probably 15 years ago. Then I noticed that the pins have a hole near the bottom to accept a "clip". Ever since, I insert clips into my hitch pins, and haven't lost another since. https://www.lowes.com/pd/Hillman-2-Pack-2-3125-in-Hitch-Pin-Clip/3012925

My trusty B2910 seat is starting to fall apart....after 18+ years. I intend to replace it in the next few weeks, and am looking for suggestions as to who sells the best seat....with arm rests. I want something that is well built, and will hold up for years of use....would rather pay a bit more...

I have a B2910 that I bought in 2002, and it has about 850 hrs. on it. Today, I was moving some dirt for a couple of hours, and everything worked fine. When done I drove near the house to rinse the dirt out of the bucket and when I tried to start it after sitting for 5 minutes, Nothing...

I have a nice Kubota B2910HST that I bought way back in 2002...when we retired to 40 acres of forestland. This past Winter I noticed slight oil leaks from 2 of the hydraulic cylinders on the Loader. It's not much, and just leaves a few drips on the floor of my workshop. Now that warm weather...

I have a nice B2910 with a La402 loader that I bought new in 2002, and only have about 850 hours on it. Over the past few months, a couple of the hydraulic cylinders have developed minor leaks....nothing severe, just enough to leave some oily spots on the workshed floor. I've only had to add a...

I was going to go out today and clean up a bunch of wood shavings where I had been doing a bunch of log splitting. However, when I tried to lower the implement arms to attach my landscape rake, the arms didn't move...even standing on them didn't lower them. So, I went back into my workshop and...

My trusty Kubota 2910, which I bought in 2002, is showing its age in the seat. The vinyl seat cover has developed several cracks, and I have it held together with Gorilla Tape, to keep the foam from popping out. I have found several sites on the Internet for new seats, but I would like to hear...

The seat on my trusty 2002 Kubota B2910 has just about worn out....major cracks in the seat covering, being held together by Gorilla Tape. Does anyone have a good proven source for a new seat? I found this one on the Internet, and am thinking seriously about ordering one. Has anyone dealt...

It's time to replace the filters/fluids on my 2002 Kubota b2910....it's been a great tractor. I prefer to use WIX filters, and I noticed a different PN for the hydraulic filter on the Wix website. I figured perhaps Wix had updated their PN's since this tractor is several years old. I had a...

Today, I was cutting down some dead trees in the forest, for Winter firewood. I took down a huge Oak tree, and it fell into a heavy growth of underbrush and thorn bushes. I decided to tow it to a more cleared spot to cut it up. I hooked up the tow line, and began moving it....4WD, Low gear...

In recent weeks, I've noticed a slight oil leak on the workshop floor coming from one of the hydraulic cylinders on my LA402 loader. It's not a big leak, and I'm hoping it is just seeping a bit around a seal due to this extended period of brutally cold weather. However, just in case I need to...

I've got a minor problem on my B2910....the vinyl seat covering is coming loose from the cushion. I would like to find some way to glue that down before the seat cover begins to fall apart. I am thinking about injecting some contact glue into the area with a hypodermic needle....the glue...

I had a first time experience today. I was running my B2910 steady for about 2 hrs this morning, and I shut it down for about 1 minute to get a drink of water. When I came back, it wouldn't start. It cranked over normally, and usually starts after just a couple of revs, but it acted like it...

I just finished rebuilding the front axle on my B2910HSD a few days ago. One of the Korean bearings on the Spiral Bevel Shaft (Pinion Gear) froze up and spun inside the axle housing...ruining it. The total parts cost was about 648 dollars, plus about $90 for a Kubota maintenance manual. I...