Recent content by denjen

  1. D

    3515CH HVAC

    Yes, condenser and receiver are combined on 15 as well. I cut/pasted from the schematic about the pressure switch. I traced the lines from the evaporator all way to the compressor and couldn't find a switch in the line, so if somebody that has a 15 series knows where it is please add it here.
  2. D

    3515CH HVAC

    Thought would update for others that might have this issue Symptom - No cold AC, compressor clutch does not engage Troubleshooting 1) Test compressor clutch engages (unplug compressor and jump from battery) 2) Use gauges to check refrigerant pressure Engine and AC off (static - is...
  3. D

    3515CH HVAC

    LouNY, thanks for the reply, I did notice the manual shows 4 relays (relay set) under the dash; but it has 5 relays and none of them are labelled. I will review the schematics some more.
  4. D

    3515CH HVAC

    Figured I would add this my original. The AC has stopped again. I just recently decided to look into before taking to a dealer. Symptom - No cold air, the compressor clutch is not engaging Past work - Dealer replaced compressor, condenser, evaporator and control module (basically new system)...
  5. D

    2515H Bent Loader hydraulics

    False alarm, it was late last night and so didn't really look into. I had a chance today and both rams where straight so found one of the lines (assume it controls the bucket tilt) had popped off the control value right under the deck. I still would appreciate opinions on cylinder replacements...
  6. D

    2515H Bent Loader hydraulics

    Ok, it appears I have bent my tilt cylinder/cylinders as I can't tilt bucket back fully. I will verify tomorrow and may attempt to straighten them out. If that doesn't work I have seen references to 3rd party. What size do I need for BL150 tilt cylinder. Thanks much for the help!
  7. D

    3 pt stop

    I finally decided to make a stop for my 3 pt on 3515ch. Now, it is a bit rough as the only tools I had were hacksaw, file and drill. I used 1/8" x 1-1/2" aluminum bar stock. I stacked the base pieces together and created a moveable stop piece. The base pieces are ~ 6-1/2" long. I have used to...
  8. D

    Branson Parts

    That is a good point as well
  9. D

    Branson Parts

    Thanks guys; but wait why does it have a DOC when that is not required since it is under 26 hp? So, are people buying the 2515 under the assumption there is no emissions? Asteral, you think they are trying to streamline parts, have to wonder if new muffler for 2515 is same for say the 3515. That...
  10. D

    Branson Parts

    I know some have swapped out the tier 4 muffler setup for a I think a Stanley muffler. Well, I thought I would see what a 2515 muffler would cost as an alternative to this approach on a 3515 for a what if scenario.... Well that was a short lived thought as the muffler for 2515 is ~$1,200! Does...
  11. D

    Battery terminals

    Interesting the replies here and honestly I posted this more as a public service announcement. Those who wish to criticize no problem go for it since they are not high on my priority. It is funny though how those who want be critical state they don't post similar situations so others might learn...
  12. D

    Feeling

    Use a 55 gallon drum with hand pump in the drum. It also has an inline fuel filter. I built a small enclosure for the drum and I have a lift strap on the drum and use the loader to put it in the truck when need to get fuel.
  13. D

    Battery terminals

    ptsg, no worries and agree not a fan of that style, so went with the older style and modified it. I can't believe how thin those new style are, probably cheaper to manufacturer. Branson Bob, sorry the battery is the original.
  14. D

    Battery terminals

    Branson Bob, the tractor is 2019 and purchased new. Uh, 5030, yes I own up to ignoring the terminals and they are fixed properly now; but don't not a fan of the attitude.
  15. D

    Battery terminals

    Thought I would post this as an FYI to check battery terminals. I had an issue when i turned on tractor the tach and temp needles started bouncing around and the hour meter went dead. It was a bad ground and found both battery terminals being eaten through. I honestly ignored them when checking...
Top