Recent content by Desert Bred

Thanks Wb I had no clue whether or not they were the same so I found a manual on eBay and finally a parts manual for the ts254.. To reciprocate, if anyone needs any specific pics of the manual let me know I'd be happy to send them your way. Includes ts-25a 25k 25y 300a 254 304a. I also had...

Hi guys. I have an issue come up that I can't identify the parts to be able to purchase. I'm including some pics and as well the manual PDF shot that I circled a few of the parts that I think need to be replaced. Only thing is I don't have the corresponding names, so if anyone has a copy of...

Ok.i just read the conclusion of 2x 12-2 romex would be better. Then could've used it after the job to wire the stalls. Anyway, got in my car earlier to pick up some wire.sat there . Read some more replies about generators and looked on Craig's. Found one (UST (5500W) for $350. Got down to...

Lincoln 140hd says using a 20 amp breaker is ok and I haven't popped it since using that breaker. And will be welding same type of metal and .35 wire. I'm shooting for the thhn wire 10 gauge, cut into 3 pieces for each : +,-, and ground. I can get 500' for 50$ I'm about to run the voltage...

Have a 140hd Lincoln welder that if like to use only that I need it 160ft away from the nearest 20amp outlet. Instead of using 10-2 romex with plugs on either end, AND because it's a one time job and in could use 12-2 wire... Is it possible to run 2x 12-2 wire instead ?

I picked up a Turf Ex 1875 spreader from an auction. The unit is a fully 12v unit that can be mounted on trucks atv's tractors etc. There are separate motors for the hopper auger, spinner, and vibrator. There is a wiring harness or something that i forgot the name for that ties in all those...

I put a hole in my radiator and was wondering if anyone out there might have one that would fit and would like to sell - db

Hi guys. I've been having some troubles with my electrical system whereas i am blowing fuses - a type of fuse that i hadn't seen before where there is extra wire wrapped at the head of the fuse - to use when the fuse fails. there is no glass to these fuses.. anyhow.. i read a post about a...

So many thanks for that link I have been looking and to no avail.. I found those other pictures - the plumbing diagram.. here now the question i have is - are the pressure gauge and the pressure relief valve plumbed oppositely.. that after the roller pump comes the relief? so the series is...

What could cause it from pouring out of the cap overflow drain pipe? I was using it digging a hole and heard the oil pouring out.. **** off the pto and it kept pouring out (pump attached)??

Hi fellas I bought a pto water pump with max 19.6 gpm -300 psi max.. http://bit.ly/1oTApFpLink... I have been utterly unsuccessful at finding a pressure relief valve / unloader valve that would be good for this pump. Something reasonably priced (@20-30$).. Does anyone have some expertise on...

Looked at another model : says Pump shaft rotation: CCW the Ferroni says CW. my pto goes CW.. so the pump should be for CCW 'When direct coupling shafts, always MATCH THE OPPOSITE ROTATION pump with the shaft.' but on ruralking the answer to a question about a pump (Shaft Size: 5⁄8” solid...

Ok me wants this but me don't know where to buy the pump for sure.. Is it a hydraulic motor connected to water pump or is hydraulic motor/pump same.? http://www.youtube.com/watch?v=-HBBdcmo92I&sns=em Sent from my iPhone

Right behind the High Low gear shifter there is this part that has finally crapped out and without it functional u have to jump the tractor from the starter.. Two wires that connect to it, I tied together to simulate a closed switch- to no avail- I still have to jump it at the starter. Is...

I'm a bit worried to see a tinge of oil leaking from the front axle in what appears to be a tiny crack. What would you guys do in a situation like this to prevent it from getting worse? Thanks Db