Recent content by gooffer69

Let's hope the picture shows up. I am searching for a T4 to buy... ran into this one. Missing for me the most important attachment it's 655 loader, curious can this be added ? I don't see the mounts the tractor would need. Also can anyone make out from the picture if this is the 4WD version...

Nope it's not the temp that is the problem... it's some resistance somewhere. Battery checks good, Glow checks good, Starter has already been changed, 8A fuse with replay has been changed. I turn the key, orange glow lights will come and she starts.... well sometimes she does. Other times I...

Just tore the bottom of the spindle/ blade bar and I found the 2 blades marked woods 127.... but there are no other marking on this 7ft cutter... trying to find the right part but I don't even know who made.... used to be blue...

Just picked it up today works nice and at $500 delivered I can't argue with its usefulness

I don't think this was ever sold in the US, I wonder WTF who made such a dump decision ? I saw the KingKutter kind... big and $$$ .... I had one of these Kubota once before I cannot rave about them enough took about 3-4 buckets of dirt and was very fast dumping.... anyone know what the model...

Well after I finally hooked up my BH7500 to the joystick directly so it's on all the time when I run my tractor I still have the rear remotes unused and I ran into a BobCat 70inch plow...... and really also want a grapple for moving around brush the pallet forks are only good to a point...

So I finally got it all hocked up and some questions I don't know the answers too.... 1. I have 3 hoses at the BH7500, 1 comes each lower side of the control valve unit and one is plumbed out of the top right looking at it from the operators seat, on the TC45DA I have a continues power loop...

Well I got the kind that has a subframe, I bolted all the bits under the TC45 today wasn't too hard the manual says to use metric taps to clean the holes I used a pipe cleaner did the job and I got everything tied down. Except there is 2 brackets that go into the 16DL loader mounts, I don't have...

well front hydraulic blowers need a lot of GPM.... manual says total GPM for TC45DA is around 14.5... but it devides into 9.8 for hydraulics and 4.7 or so for power steering.... now when looking at a snowblower can I shop 10-14 gpm kind or do I really need to stay below 10 :(

Anyone tried this ? I have my doubts if it's possible.... my 54 CMS deck goes thru front wheels like it's going out of style... I know grease and adjustment but the construction totally sucks, the 914a deck the front wheel can pivot the 54/60 CMS decks are fixed hence you wear out front wheels...

Picture always better.... problem is to the right is something that holds the rollbar/ cab support that prevents drilling access....

So I undid the little 9/16 both that holds in the pin for the lower control arm on the right side... couldn't get the pin out. So I did the same thing on the left side and the pin came out while spinning the hole bolt/pin using a 3/4 spanner.... Then went back to right side, no go.... heat , WD...

Well got lucky my TC45 came with a spare rim and tire for the front but after 3300h it's getting a little old all 3 front tires have seen their best times... 8 x 16 Titan's... well I have loads of 16" tires kicking around one set is a 8ply 7.50 x 16 the other a 10ply super traction 245/75 r16...

266hours safety switch on the seat works, safety switch on PTO tested. fuel pump is heard and filled up bowl after changing fuel filter. cranks over but not start. stalled after running for 30 seconds when I pulled it out of the barn. I changed fuelfilters, fuel to filter no problem. I...