I have 4' Land Pride rotary mower and a 5' Land Pride finish mower I pull with our B2920. Can someone point me to a video or thread that shows me how to grease to pto shaft and u-joints.
I have googled all around, but have not found anything that shows me how to remove the Italian made PTO...
When I was installing the sub-frame for my new BH65 back hoe, I noticed that the hydraulic filter (filter on the right side) was bent up pretty badly. Apparently I had done this bush hogging some rough mtn land we own. I had chopped off a lot of locust, sassafras and buckthorn trees with a...
Hasn't happened yet, but I use my tractor way back in the woods and sooner or later I know I'm going to break something I can't easily fix. Can I put the tranny in neutral and tow it back to civilization with a tow strap behind my jeep without tearing something up? It would get towed about 2...
I've called a couple of Kubota dealers to get pricing for a BH65 and sub-frame for my 2012 B2920. They all seem to be about the same price. Do they ever put these things on sale or offer specical financing? Are there any dealers offering lower pricing? I should have bought it with the...
I guess my B2920 was designed to operate this way, but it is really annoying to have to keeping looking back there to see how far the front of my rotary cutter has sagged and them bump it back up to the correct height.
Seems like I have to bump it back up every few minutes. Anyone put limiting...
I would like to replace the turnbuckles on my B2920 with telescopic stabilizers. Where have people bought those recently? I read quite a few posts about the ones M Hodges made, but his web site is down.
Also read a few posts about some from Tractorsmart.com, but I couldn't find them on their...
I bought a new B2920 w/FEL about 2 years ago. At the time I planned on getting it with the Kubota backhoe, but got talked out of it. I have regretted that decision ever since.
What would it take for me to add the Kubota backhoe at this point? I understand a sub-frame is required. Is this...
This is my first tractor and I thought I knew how the 3pt hitch worked, but now I'm beginning to think I don't.
When I use the rotary cutter, I lift the front of the deck up with the hand control lever to almost level with the back of the deck. It seems to work fine like that except that the...
I came across a good deal ($100) on an old 4 angle iron single row disc harrow. All I want it for is to rough up the ground a bit to plant grass or whatever for some small food plots. I tried it out in my backyard and have a few questions.
1) I guess I'm not exactly sure how my 3 point lift...
Siphoned 12 gallons of 0 degree Walmart windshield washer fluid from a 5-gallon bucket into each rear tire. Lifted the rear tires slightly with a floor jack and deflated them. The tires seemed to be a little above the level of the axle. I believe 15 gallons would have put them at the 3/4 mark...
I have read the same posts about interference problem with rear wheel spacers and a MMM. I can't answer because I don't have the MMM..... but I would think that a couple of hours with a cutoff wheel, a mig and a can of Krylon could move those rear mmm wheels over a bit and out of the way.
Received our 2" wheel spacers from Bro-Tek a few days ago and finished installing them on our B2920 Kubota this morning. As others have said, Richard at Bro-Tek was very easy to deal with and shipping was fast.
I had a few of concerns before ordering the wheel spacers.
Concern 1 was the...
Searched around and found some ideas/photos. Seems that CJ mirrors are the most popular option, but some have commented that they shake/vibrate.
Anyone added mirrors which they are very happy with the results? My main need for them is to see behind the bush hog when I'm backing up in the...
http://www.tractorbynet.com/forums/kubota-owning-operating/209290-wheel-spacer-b3200-question.html
Finally found a photo of the Kubota OEM wheel spacers.