Menu
Forums
Today's Posts
New posts
Search
Members
Current visitors
New profile posts
Search profile posts
Top Posters of the Month
Marketplace
Register
Log in
Join
What's new
Search
Search
Search titles only
Today's Posts
New Posts
Search
Members
Current visitors
Top posters of the month
Menu
Log in
Join
Forums
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
jigs_n_fixtures's latest activity
jigs_n_fixtures
replied to the thread
Warranty misleading
.
Guys: most of you are as old as I am. I remember inflation at 7%, with a prime lending rate of over 12%. They called it stagflation...
Apr 12, 2024
jigs_n_fixtures
reacted to
5030's post
in the thread
Warranty misleading
with
Good Post
.
What I find amazing is, the amount of owner abuse the smaller tractors take before failing. To me, that alone is a testament to their...
Apr 12, 2024
jigs_n_fixtures
replied to the thread
12mm Female Square Drain Plug/ Pipe Plug Socket ?? TYM Front axle drain & Vent pugs
.
Those are all “male”. The plug has the 12-mm square male hex protruding, and he needs the female socket.
Apr 12, 2024
jigs_n_fixtures
replied to the thread
12mm Female Square Drain Plug/ Pipe Plug Socket ?? TYM Front axle drain & Vent pugs
.
8-pt 1/2-inch socket will work fine
Apr 10, 2024
jigs_n_fixtures
reacted to
BigGG's post
in the thread
12mm Female Square Drain Plug/ Pipe Plug Socket ?? TYM Front axle drain & Vent pugs
with
Good Post
.
8 pt socket?
Apr 10, 2024
jigs_n_fixtures
replied to the thread
Any Sparkies? I need wiring help
.
Thanks guys. Need to start pricing, and researching a bit more. Have to go out of town for a few weeks, so the project is going on...
Mar 30, 2024
jigs_n_fixtures
reacted to
Roadworthy's post
in the thread
Any Sparkies? I need wiring help
with
Good Post
.
The SJOO would be a 300 volt wire while the SOO would be 600 volt. The W indicates it's for wet locations. I'd check the LED current...
Mar 29, 2024
jigs_n_fixtures
posted the thread
Any Sparkies? I need wiring help
in
Build-It Yourself
.
I am going to wire some auxiliary lights, and solenoid driven diverter valves. The wiring will be exposed to sun and weather. Is...
Mar 27, 2024
jigs_n_fixtures
replied to the thread
death of regular cab pickups
.
I started looking for a diesel, standard cab, long bed, with a manual transmission. Ended up with an 08 Dodge 1-ton, mega cab, with a...
Mar 27, 2024
jigs_n_fixtures
replied to the thread
death of regular cab pickups
.
They stole your saws, because none of the rental places, had saws left. I ended up with a 20-inch electric Chainsaw after a high wind...
Mar 27, 2024
jigs_n_fixtures
replied to the thread
T273 - Another broken driveshaft/input shaft
.
The manuals Operators/Service/Parts for the T233 and T273, are readily avaialble if you search for them.
Mar 12, 2024
jigs_n_fixtures
replied to the thread
Need help identifying the PB and T ports
.
Just an FYI for folks finishing this in the future: Typically, the valve itself has the port identifications cast into it.
Mar 12, 2024
jigs_n_fixtures
replied to the thread
All thread rod as rebar
.
But, no matter of how deep you embed the bar, the chlorides will penetrate far enough that it willl corrode. Which is why for bridges...
Mar 12, 2024
jigs_n_fixtures
reacted to
Zigblazer's post
in the thread
Why so much tongue weight on 22' car hauler trailers?
with
Good Post
.
I've looked at this thread many times. I keep thinking someone will bring up the other side of the safety issue, because too little...
Mar 12, 2024
jigs_n_fixtures
reacted to
MH8675309's post
in the thread
Why so much tongue weight on 22' car hauler trailers?
with
Good Post
.
Well, I did
Mar 12, 2024
Forums
Top