Recent content by Kendrick

I have been switching over my equipment to the lever tighten battery clamps due to that. since they are adjustable with out using tools and will keep the proper setting even after removal I don't have to worry about is it to tight or to loose.

To answer the question a pair of tweezer pliers see 5 in. Tweezer Pliers two side tabs that were an absolute bear to get. some tiny modeling u channel / box might work to free it up. maybe 2 pieces of small bar stock would work to 14/12ga thick maybe.

I have had to resort to the aluminum mesh like what you use for gutters to keep the leaves out you can buy a 4'x8' sheet at home depot in the concrete isle. that stuff is good for blocking the air vents. I had to do that with a window AC unit it was put over the blower vent inside and the 2...

here are some pics. I have tried the top and bottom no way to get any thing in there to unhook it. per pics below it might be sides but i have sent a screwdriver and pin release tools down both sides and tried using one to pull up on the holder while the pins

I need to replace a line in the fuse box. I cannot figure out how in the world to get that terminal out of the fuse block with out cutting it out. I am talking about the part that contacts with the automotive fuse.

Replacement Cab Lights - DK45s (2006) here's a good set of pics of it. they included a decent replacement. i went with fabbing a frame for the rear to add a bar and the fronts I will have to see how well the wire plugs the hole if i can get away with using a grommit plus wire ill be happy.

Im in the process of building some brackets so i can fit a 32" light bar from harbor freight on the back of mine. I have a HF 3" light set for the front. for me the backup lights is far more needed as the snow blower runs the most during the dark. also adding a backup camera just below the...

I have a dk45s cab that the door caught on a limb and pulled out the door piston and has damaged the door seal. Does anyone know if that's repairable or a door replacement?

I am needing to swap out my work lamps on the tractor and was hoping to find a replacement set of gromet bolts that allow the wiring for the lights to go through it while bolting the light frame in place. The ones i have were bent to death and im hoping to go with led lights now instead of the...

I need some one to verify that the grease point on the lower end of the arms. I had been good about greasing all the points and just recently it started squeaking while i was greasing for the anual post winter cleanup I realised that the bottom pins on the arms dont have ANY grease points and...

I am getting started on a generator frame that will allow me to use both my tractor pto and my lawnmower to power the generator as needed. I am having issues finding some reasonable information about shaft sizing for the shievs. I also wonder if it may be more reasonable to use 2 steps from...

I had run the pto yesterday no issues. I started th bailer up today and it turned over the pto for about 10 sec or so and kicked out. now i cant get it to turn at all. I disconnected the bailer tried manual and auto no change. the light on the side of the cab lights up to engage the pto...

I have a stick welder and need to remove 3 recessed special shaped screws for my car door lock and the brake actuator on my truck. the truck bolt is straight forward and will probably not be a problem. the car is another story. They have degenerated fairly badly. I stuck a screwdriver in...

I have a project where i have 1" box inbetween 2 3" angle pieces. they rest aginst the back stop which is also a 3" angle. I was trying to think of the best way to tie all those pieces together. my first thought was to weld the box to the back stop so that it has 3" of weld aginst the back...

I have some impliments and tractor bits I need to get painted. Started looking around at paint and need to figure the difference between the valspar oil vs tractor & impliment. Does any one know the difference wear wise and fading wise etc. im also interested in how it ends up looking with...