Recent content by kidkioti

A brief update .... Was able to jack up the tire off the ground, as suggested and put a couple of ratchets around the tire. Then took a rubber mallet and started to rotate the tire and hit the side that was not seated. After some time and putting air into the tire the tire finally seated on the...

Thanks for the suggestions. Maybe I can follow through your procedure or try to remove the tire & wheel to take to repair shop. Your procedure is most cost effective. Hopefully I can make some kind of progress on it today.

Appreciate the reply & suggestions. Hopefully I may be able to get something to work. Thanks for taking the time & your suggestions were helpful. Most all the repair shops I called prefer to replace the tube.

Checked around and about the mobile services some offer. Not sure what this tire & wheel weigh? Unloaded & maybe if I remove the chains this SC may be able to handle it?? 500 lbs that's pretty commendable. Thanks for the reply!

Just noticed that looking at the rear of tractor the right tire on my Kioti CK27 is flat. Further inspection, I noticed that the tire is separated from its rim next to inside of tractor. Tire size reads 15-19.5 8 ply. I would appreciate our forum advice or suggestions on ways to repair this...

This SC has a CK 27 that currently has square link grader chains installed. Correction - currently have just one side as I lost one during last snow storm in Pa. (again). Rather than high-jack the previously thread ... would like to have others of our family forum share or or suggest what they...

Dear Friends ... My CK27 currently has 650 hours. Have owned it for going on 6 years. Has anybody had to have the Front Axle Pivot Adjusted or Have had to have the Engine Valve Clearance Adjusted? Have not had any serious problems/issues with the tractor. Have been performing periodic services...

Came across a thread that mentioned, AT ONE TIME, some years ago, that .023 fluxcore wire was manufactured and available for the fluxcore and/or Mig/Fluxcore welders. Thought I would check this out with the Forum to see if there was any credibility to this? If so, would like to know if it may be...

What is the preferred distance for the length of wire to be exposed from the tip to the work piece to provide satisfactory welds. Its becoming more difficult for this Senior C to see the end of the wire because the nozzle blocks the view? Hobart offers an optional gasless flux core tip for this...

Purchased the CK27H New in Spring 2011 less than 400 hrs. Have a starting problem. Turn the key on until the pre-heating light goes out. Pedal is depressed & key is turned to start position. When turned on, I get a groan from the solenoid or starter but the engine does not turn over. I've have...

There is a private road RUNNING through my property that was abandoned when a new road was built, approx 7 years ago. Length is about 170 feet that ends in a dead end. I was informed that the original rights of way continue to exist. It is abandoned and returning to nature. Any suggestions...

Some years ago ( approx 5 ) a private road ( approx 1/2 mi ) was needed to be constructed to provide the residents with a way out. Road was constructed next to my property. I was informed that additional construction was going to be needed so this road could be surveyed, a maintenance agreement...

Have a CK27HST with the KL 130 Loader. Since day one I've noticed that it operates more like a spring board. I notice this more so when it has a load. Trying to maintain a smooth & complete control going up or going down with the joystick is touchy/erratic. When bringing the load down, it may...

Dear friends - Hope I got the right forum? If I'm wrong, please tell me where to go? Have a simplicity hydro stat that needs attention. Where/who sells replacements or repair parts, for these units. Where might they be available? Perhaps some of you may have worked on your own hydro and are...

Would like some input on this matter before I call dealer. Have a Kioti CK 27 HST that I purchased March of this year ( 54 hrs ). In the beginning, things were normal. It started appropriately the first time. At times, it began to just turn over on the initial try but not start. After repeated...