Recent content by klink

Thank You

Thank You for responding with good info

1960's John Deere 2010 utility tractor power steering issue. I am a retired Mechanical Maintenance person wanting to help my son, who is a hobby farmer. I am looking for some verbal help or pictures relating to a 1960's John Deere 2010 utility tractor power steering issue. The tractor has...

I didn't read all the posts, but I will add a little info. I have been to a lot of quarries or bulk loading docks where they have rules that the driver must stay in the truck at all times. That may work for the big dump trucks with automated tarps and such. but I like to do a walk around making...

my John Deere 520 when the engine is running the tractor ammeter fluctuates radically on both sides of 0. Just bought the tractor and it has a new battery in it. It has all original wiring and still has a 12 volt generator with positive ground. the battery voltage seems be ok, with a hand held...

I have a 660 Ford [600 series] I have only owned this tractor for 3 years and don't know the history - I recently replaced the distributor cap and rotor - the old rotor had a little medal clip that went in side the rotor shaft hole. I tried to put the clip into the new rotor, but could not see...

I use a Ford 660 tractor for club tractor rides and I would like to temporarily tie rear brake pedals together whenever I am on the road. I was wondering if anyone has done this before, so that I don't have to reinvent the wheel. Thank you in advance. Klink

Hi How hard and or expensive is it to replace a bad TA in a IH 350. I've never had any experience in replacing or repairing a TA on old Farmalls. Any and all info would be appreciated on the subject. I did not do much searching in forums on the subject. Thanks klink

Hi My John Deere 50 is a hard steering tractor, with an extra hard spot about half way through a full turn when turning left. I took off the front nose hood cover and checked the oil level in top steering gear box - it has plenty of oil in it. that's as far as I have gotten. I plan on blocking...

Where can I get a side cone drive pto clutch drive pad disc. I live in NW Ohio area. I need to know where a Wheel Horse salvage yard is at. or any help in locating cone pto clutch parts. I don't think we have a Toro-Wheel Horse dealer in Findlay, Ohio. Klink

I had the main fuel needle out of the carb & was blowing light air from compressor into the various carb holes to get any dirt out. Out of the corner of my eye I seen some thing fly out of the main fuel jet hole on top of carb. I looked around but could not find anything. I know I blew something...

I have a Cub Cadet 1541 with a very slow reverse speed. I was wandering if anyone has ever found a way to speed the reverse speed a little faster. I realize that reverse should be slower than forward speeds, but mine is really slow in reverse. Any insight on this problem is welcome. klink

I want a Pequea 1020sst [ 12k x 20' ] trailer with 8 bolt hubs, new 235/80R/16 tires, 10k drop leg jack, led lights, 6' spring assist ladder ramps, one spare tire. Price quoted - with tax included - $6750. I would appreciate some feed back from some of you, that have priced out similar...

I have 2 John Deere mowing tractors ( GX345 & X540 ) with 54" mower decks. I don't like the high suction blades. They suck up stones along driveways and throw them out. Also their shape makes it hard to sharpen them. I would like to try a set of aftermarket straight blades that just cut grass...

My son asked me to make a calf or cow walker tractor hitch to use to train larger calfs to walk with his teenage kids. I know, they should walk the calfs daily, so that it is a gradual training process. Last years dairy show calfs are going back to the fair again this coming summer. So I'm...