I have a B2320DT and curious if I can safely go down this path and up.
I want to go along the railing and it's bit narrow now but I can widen it.
Brush near bottom might be hiding the steepest part.
I may have to back up, up the hill for now as well.
I need to haul a bunch of soggy dead wood...
First I know this trailer is not ideal. It is not primarily for moving the tractor, but I'm curious if it's an option or not to just bring tractor in for service once in a while.
This trailer has a GVWR of 5000 LBS. It weighs 1420 LBS and that leaves 3589LBS capacity.
My B2320DT weighs 1433...
I plan to buy one of these Hydraulic Dump Trailers (see image links below).
I don't plan to Haul my B2320 Kubota in it.
But I have a rear implement beach cleaner that has a hydraulic dump and I've been using a very low utility trailer that has a deck height of 18" to dump onto directly from...
On my B2320 the temp gauge has been reading very low for a long time.
Finally I decided it was time to fix it.
9 times out of 10 it's the sending unit.
I shorted the lead to ground going to the gauge (at the sending unit) and it pegged the meter.
So I ordered a new sending unit.
I...
It seems nobody is happy where the "Standard" location of these kits are installed (on the outside of the ROPS).
I tried something a little different than other folks. I flipped the remotes upside down as I moved it inside.
I think it worked out nicely. I think if I didn't flip it, it would...
Are there any sources for Box Blade Dolly's or Dolly's flexible enough to be used for one.
The edges are fairly worn so it does not sit flat on it's own. And I don't keep tines on it normally.
So I need to have some support on the main crossbar. And Ideally adjustable.
Any home made ideas...
Doesn't it make sense to use a male and female on each valve so you get consistent direction correct?
Looking on the web I see a lot of folks put all females on their remotes and all males on their implements.
The implement I recently bought (Sandman TT) came with 2 males.
What would you...
I just got my tractor back from dealer installing rear remotes and replacing hydro fluid.
I used it for like 1/2 hr spot fixing the road and moving trailer/boat around.
I then went to go hook up the new implement that I got the hydraulic remotes for.
I must have started it 10 times already...
I believe MB Tractor botched my B7309 install. Duel setup.
Does any one have the install instructions that they could possible scan and PM me?
I took all 4 couplers off and nothing comes out of any of them except a little spit when I move the controls.
Also is there any standard on what...
I plan to buy a Dumping Trailer.
Like one of these: Dumping Trailers
I thought perhaps if I got one big enough it could also be used to Tow B2320DT around.
I rarely have to tow it. But since I'm getting the Trailer any way, why not spec it for towing B2320 too.
How would Ramps work (with a...
I'm bringing tractor in to have remotes added and figured I'd let them do 100hr maintenance.
I plan to have them replace Hydraulic Fluid with Super UDT and Filter. He said the cost of fluid was like $55.00
I plan to change oil myself.
I asked him how much will it cost. Which would include...
I'm having rear Hydraulics added to my B2320 for a new attachment that requires it.
But I figured I might as well now add a hydraulic top link to my Box Blade as well.
If the Remote circuit is all set. Is adding the top Hydraulic Link just off the shelf and plug and play or is there more to...
I have a B2320 DT Tractor with just a Front End loader.
I'm gonna add Sandman TT Beach cleaner to the rear.
It needs hydraulics for dumping.
Can I just disconnect the bucket Curl and run two long hoses (short term).
Will the bucket stay put if disconnected?
If I want to add permanent...
Backup. And bringing boat for service. Towing Kubota. Love the new GC Jeep, my 3rd since 96.
I was a little worried too that the tires on the new Jeep were not aggressive enough, great on MPG though.
I've been trying for years to get my boat out with something less than my Jeep.
I decided to give it one more go. Before using my new Jeep which I really didn't want to cover in sand just yet.
Loaded up front end loader with wet sand.
Weaved ropes on front tires as a wimpy chain (I don't...