Recent content by NJBill

I know I come up with some weird questions, maybe without realizing it, I have a diagnostic cell somewhere in the gray matter. This one....... Do you all have a Blue square containing a White check mark at the Right Hand side of the thread column, any time you are involved in that particular...

No rush on this, it could be a problem. Do any of our design, engineering, or other knowledgeable person know if this symbol is representative of any particular manufacturer ?? I had to blow up a few times, but tried to leave it recognisable, it is located on the power plant of a PT. Thanks for...

Hi, My name is Lubey, I come from a very, very, big family. I was delivered to Power Trac, and was assigned to a 422, so my permanent home is in the twelve gallon tank right under the driver's seat. Our duty is to serve the owner at any time without warning, it's kind of like a waiting game. I...

When there does not appear to be any type of emergency visible, does anyone know the average waiting time, for answers to reasonably common sense questions, submitted by Email ??

Does anyone know of a problem, or other reason, which may occur if elbow fittings are installed on the Hydraulic motor, I believe the routing would not be affected, and I could lower the suspension point of the mower, by possibly two to three inches. The sides of the motor appear to have been...

if you receive this, I will never know. I sent an email to contact source of TBN telling them of a Norton pop-up to say they blocked an intrusion to my PC, every time I tried to enter Power Trac Forum. Since I sent the email I don't get the Norton Notice but I still cannot enter the PT Forum...

Leaf season almost ending, and wouldn't you know my six year old leaf rake, finally needed it's second blade. Even had to glue the handle together which split dead center. This is one hand tool I really enjoy using, I don't have to keep cleaning the leaves out of the teeth. I'm currently working...

P T O Please forgive my laziness, that is reading back posts. I'm sure someone has this information at his/her finger tips. I'm looking at an implement which can be supplied with either of two values, namely a 540 PTO, or 750-900 rpm. 13.5 is the required HP. Each time I read a post concerning...

pajoube\'s PT\'ers by state As some of you may have noticed, I have been around for quite a while. ( only a short time as a PT er ) In my few leisure moments at the store, or in a parking lot, I find a lot of enjoyment just watching people as they do their normal things. I call it post-college...

I ran hard into a banked area while turning, with the mower set on float. Uh uh Correct ! Just pushed the right front caster tire off the rim. Up until this week, I did mower aservice with a chain hooked under the front wheels, and lifted with the Q A Plate. NO MORE, I like the new way much...

Hi folks, this information may be redirected to another column, but I thought I would like my PT colleagues to view the idea. Picture the added possibilities for your PT with this cutomization. A family friend just purchased the first one. after you click on the address below, go to the blue...

MR Because of your excellent pics of the slime situation, I have always avoided any similar magic potions. Just a couple of points which I have found to be fairly foolproof. even though I speak from the automobile trade, they've worked. Tires kept at 5 lbs higher than posted on the door...

Hello ! Fellow P T'ers. To me this part of the P T became a mystery, and mysteries need to be solved. In case you also wondered, here it is. It's hundreds of years since I was introduced to Practical Drawing, probably a couple of years before I finished school at age 14, so please forgive me if...

Hi Folks, and the group is enlarging very fast this year, incidentally welcome to all the new names I am met with each time I log on. I didn't know where to start with this particular question, so I figured home base would be the best place for a PT'er. I have just finished recently installing...

My thoughts flew to MR quite a few times as I was uprooting unwanted trees and bushes, I am still doing more. Even though the NJ sand [sorry, soil] is light and loose, when I did the planting, I didn't know any better so I covered everything with landscape fabric. Have you tried pushing a spade...