Recent content by Pipestone Kid

I sold the homestead and my tractor is going to my son in Arizona. Needless to say, he doesn't need a snowblower. Therefore my blower is for sale. The info I have said it fits a JD 4100, 4110, 4115, 2320, 2025R, 2520, 2032R, (910) It is used, but in good condition. $ 1,000. If interested, send...

I am trying to change the fuel filter on a JD 4110. The filter may be frozen (I got the 4110 running after a treatment of De-Gel) or ti is just plain tight. I am assuming that it is standard right hand threads--or am I wrong? I can't get the nut to turn to open the filter case. Any ideas would...

I have a JD 4110hst with a hitch problem. There is a lever on the right hand side (as you sit in the seat) that raises and lowers the three point. There is also a sliding stop to facilitate maintaining a certain height for the attachment, if need be. The lever travels about 7 inches (+ or -)...

I have a John Deere 4110 with, among other attachments, a 47 inch front mounted blower. My place is for sale and as soon as it goes, the tractor and attachments (minus the blower) are going to my son in Arizona. (He doesn't need a blower) The blower is complete with quick hitch etc. I am trying...

The control lever for my 3 point hitch (JD 4110) has graduation from 2 to 9. When new, I could set the lever at the lowest point (2) and the back blade would be all the way down. As soon as I moved the lever up just a little (i.e. to 3) the blade would raise a little. (like it should) Now I have...

House is up for sale and when it goes, I want to transport my JD4110 (cut) to my son in Arizona. (I'm in northern Minnesota) I'm looking for advice on truckers: trailering: or whatever. I want to send the tractor, FEL, back blade, and a few small items. (My 47 inch blower will go on the market...

I have a 2004 JD 4110 with a JD block heater. Is there a test I can do to see if it is working? This morning I had it on for about an hour and a half. When I went to start it, it turned over rather slow, but started OK. Of course, one other possibility is the battery is getting tired--it is the...

Here are some pics of my $20 lights (the wiring kit includes a separate switch) Mine are mounted on the canopy of my cab, but could be on the ROPS or anywhere. P.S. They are halogen

I didn't get any response on the JD part of this forum, so I thought I would ask the same question here. "My 4110 has a lever to raise and lower the three point. When new, I could adjust the height of the blade by setting the lever at any point along the travel path of the lever. Now, I have to...

My 4110 has a lever to raise and lower the three point. When new, I could adjust the height of the blade by setting the lever at any point along the travel path of the lever. Now, I have to pull the lever at least halfway up to get the blade to move. ( same going down) Any thoughts?

My4110 three point has a lever to raise and lower. The travel are of this lever is graduated to adjust the height of the back blade. When either raising or lowering, the blade does not move on the bottom half of the graduations. (i.e. I have to pull the lever half way up before the blade starts...

Lately I have noticed that the 3 point hitch on my 4110 doesn't start to raise the back blade until I move the lever about half way up. I still goes up all the way, but I don't seem to have any adjustment in the lower half of the raise/lower lever. Any ideas? Oh yes, I have checked the fluid...

I have a plate on the side of my hydrostatic transmission that leaks when I snow blow under heavy load. There is no gasket (by design) under this plate I plan on removing it and putting a sealant on and replacing it . I welcome sealant suggestions. It needs to be one that isn't affected by...

My neighbor has an old Farmall H with a 33A loader on it. The cylinders have packing and a packing nut instead of seals. Does anyone know where he can get new packing? TIA Jim

KennyD, I know you have the same tractor I do and I know you have a repair manual on CD. Could you (and would you, please) look up the transaxle and see if part # M807385 (Plate) has a gasket? I get a small drip of Hydro fluid when I blow snow--no other time. Thanks in advance. Jim