Recent content by quadpa1911

Hello to all and looking for some information. I have a new root grapple and plumbed it to the remotes on my Kioti DK45se. My remote valve has been used with my backhoe until now. When the lever is pulled up to the (A) position the grapple opens with pressure but when I push down to the (B)...

Hello All, I need more knee room than the seat adjuster allows. Has any one move the seat rail or correspondent parts back or customise your seat in anyway? I have some different ideas but want to check with you all before I go and recreate the wheel. P.S. its a DK45s (Dirty Kid 45...

Hello All, I need more knee room than the seat adjuster allows. Has any one move the seat rail or correspondent parts back or customise your seat in anyway? I have some different ideas but want to check with you all before I go and recreate the wheel. P.S. its a DK45s (Dirty Kid 45...

Hello All, I need more knee room than the seat adjuster allows. Has any one move the seat rail or correspondent parts back or customise your seat in anyway? I have some different ideas but want to check with you all before I go and recreate the wheel. P.S. its a DK45s (Dirty Kid 45...

So What type of contractors licences when using your tractor for tilling, mowing, drive way grading (Back Box), post hole drilling, and misc. backhoe work. I haven't been able to pin point anything for the State of Jefferson :) (California)

Can anyone tell me who makes the KRC rotary cutter and is a used 60" worth $500.00 Thanks, Brian

Good day from the West Coast, I'm getting ready to purchase a new post hole digger and augers. I'm looking at Land pride, Bush hog, and Woods, with 9 and 12" auger for sure, but I'm not sure if I should go with a 18 or 24" landscape auger. I have the Kioti DK45 thats rated 38 hp at the PTO. I'm...

Looking for some pros and cons on AG-MEIER PHD TIA Brian

My A-B selector would not hold in position so I went to adjust the detent and guess what? When I loosened up the jam nut it broke free and dropped to the ground. The adjustment screw was broke and the paint was the only thing holding the jam nut in place. My question is: Will the set screw for...

My A-B selector would not hold in position so I went to adjust the detent and guess what? When I loosened up the jam nut it broke free and dropped to the ground. The adjustment screw was broke and the paint was the only thing holding the jam nut in place. My question is: Will the set screw for...

I don't often review Craigslist but decided to look for a PHD and to my surprise there's the hidden jewel. An almost new Brush Hog 2103 with 6", 9" and 12" auger and it gets better it has the hydraulic down force and parking options. Well being 11pm I ask the wife to call first thing in the AM...

Just bought a new trailer after selling existing 18' dove tail car hauler (7,000GVW) and no problems loading or dragging the BH, I assumed a 14K 20' dove tail would be just the trick. Boy was I in for a surprise when I went to use it for my 50 hour service I found the BH dragging in the gravel...

I bought a 2007 DK45S earlier this year and ordered and had installed by the Dealer a new 2485 BH after using it a couple of times I thought what a pain it was to get on and off with it running as there was no grab bar and by instincts you want to grab a control lever. I was going to make...

I have a DK45S with a KL451 FEL 72" bucket I was looking into a tooth bar when the dealer I bought the tractor from told me that it would tear up the loader and bucket. I see a lot of folks here using tooth bars any problems and do's and don'ts?

First off I want to say hello to this group. I'm getting ready to pickup a new DK45S with a KB2485 backhoe and its this group that helped in making my decision on the Kioti. I need some input on a mechanical backhoe thumb for the KB2485 any pros or cons on whats out there? Weld on or is there a...