I have a 1610TS and was backing it up in the basement and the front end loader started squealing REALLY bad. Seems like it is at the hand controller for the bucket. Any ideas what to do or how to fix it??? Thanks Rambo
Does anybody know how hard it is to put brakes on a 1610TS. Also who would carry these pads. I tried to get the covers off of the brakes and they seemed to be stuck ,any Ideas. Thanks Rambo N.C.
I was mowing and I made a mistake and let the tractor run out of fuel. I put more fuel back in and it still will not fire. Somebody told me to take the injector lines loose and turn it over to get fuel out. I did and still no fuel came out of the lines. My question is, is it possible the...
I have a 1610 TS and was getting ready to change transmission fluid and was told to use hydraulic transmission fluid from a dealer and the book called for 90W gear oil. The dealer also said that it did not matter. I was just wondering what everyone else uses and also there are 2 plugs...
Hello, I have a 1610TS and I believe that my rear wheels are in lock position from the differential pedal. I believe that it may be frozen and was wondering how to go about releasing it. I noticed that the differential pedal is very hard to mash down and very hard to pull up with hand. It...
I put a 5 foot finish mower behind my Iseki 1610TS and was just wondering why it is so loud. When the PTO is engaged and starts turning, it makes a loud racket when turning. It may be normal, but just wondering. Is this normal or what can I do to quiet it down. It does have plenty of oil in...
I have 1610TS, and notice that at the back of the tractor pto hook up is leaking. Does anybody no how big of a job it is to fix.I do not no if it is a o ring, or a gasket. Thanks for any help, Rambo
I have a 1610TS, and was wondering where do you put the hydraulic fluid in for the loader. Above the bucket is a cross bar which has a metal cover to protect the lines.I was wondering how to take the lines off the cover with out the fluid running out. The metal cover is bent, so I was wanting to...
I have a Toro 266H and was riding with the blades off and for some reason, the blades came on. Now they will not turn off. I checked the pto switch and it doesn't seem to be that. Just wondering if anyone in the forum has any idea why? Or what to do?
I am looking to get a finishing mower for my 1610TS. I was going to go with a 4ft., but someone said I may could put a 5ft. mower on. I was just wondering if I could put a 5ft. on a 1610TS. I just thought I'd ask and see what you guys thought. Thanks! Rambo, NC
I have a 1610TS, and was just wondering how do you check the oil in the injector pump. Also, where does the oil go in. I thought maybe it had a oil cap w/ stick. I am not familiar with a injector pump. Thanks for any in put Rambo N.C.
I was feeling the front nuckle spindle with gear oil and noticed this morning that it had leaked out. Seems to be coming from the hub area. I took off the nuckle spindle side and I saw a big gear in a couple wheel bearings. I was just wondering is there a seal behind the hub or is it just a...
Hello,
I was just wondering what kind of fluid goes in the transmission? I put hydraulic/transmission fluid in it and now it's leaking from the rear of the PTO. In which where would you connect a mowing unit? I seen on one post where somebody used 90w gear oil. Just wondering if the hydraulic...
What is the correct oil filter for a iseki 1610TS? I heard that using the wrong oil filter could cause problems. In which I have oil coming from oil cap. I changed the oil and notice after running for about 5 min. it started coming out of oil cap. I don't know if this would cause it or not...
I have a TS1610 Iseki. Just wondering how hard it is to replace seals in spindles. where the wheel is mounted on the hub, I noticed a leak on the inside of the hub and at the bottom of the tie rod area, it is coming out from the top of those seals. Also, any idea of where I can get a manual...