Recent content by revg62

2000 model- I attempted to replace the single belt that runs from the crank,water pump & altenator.went to 2 dealers with old belt (no numbers on old belt).they look up the part number as 301525a1 which is 1/2" x 38.2".i tried to install it last night & it's too short,i can't even get it around...

attached are 2 pics of the pistons from boom cylinders.i purchased 90939 kits from bush hog & had very little trouble with everything else.however,this seal has me puzzled.everything I've been able to find says to soak it it hot water,install & it will fit when it cools down.it's not split & as...

hey all.working on a friend's 1725,found water in diesel by draining into a clear glass jar.drained all the fuel from tank,put in fresh diesel & managed to get it running good for a while then back to barely running (no throttle response).tried bleeding at injector pump,appears to be good...

hello all,i have a new holland 3415 (2000 model) that i can't get out of 1st gear on the range lever(lever next to my left leg).i was using the loader this am & noticed the clutch didn't feel right before the lever stuck.i can still use 1,2,3 & r on dash lever.range lever has always been a pita...

i picked this up last weekend for $100,can't find any manufacturer's name on it.just wondering if anyone out there has seen or owned one like this? i know i'll need bearings,a couple shafts (7/8") & some discs.looks like the 3" tubing on one side is twisted but i should have some to repair it...

or who makes it ? while checking out stuff on ebay,i ran across this item #230488369988.sorry i can't figure out how to post the pics but if i were closer to ohio,i'd check it out.thanks,revg62.

i picked this up recently,the model #/ s/n tag is missing.any idea what model this may be? one of the part numbers on a casting is:h1112-h.i appreciate any info you can give.thanks,revg62.

hi all,i picked up an ingersoll rand 2545 10 hp compressor with 120 gal. tank for free yesterday.the compressor pump is locked up,i tried to turn it by hand & it won't budge.would it be cheaper to buy a replacement pump or try & overhaul this one? i know it depends on how much is wrong with...

hi,need thoughts & opinions on towing a john deere 1010 tractor with the rear wheels off the ground.i picked up a truck last weekend like this using hay forks under the rear,raising the bed & chaining the 2 together.pulled it about 2 miles with no problems.my concern is with the weight of the...

hello eveyone,need your opinions/ideas on parting out a '52 model farmall h.it's been split in two for over 20 yrs. inside a barn.i'm taking this on in exchange for bushhogging the property.any parts in particular that are worth anything? i'd rather see them go to someone who needs them,the rest...

hello all,got my 2000 3415 delivered today.2wd,bush hog 2436 loader with 6' quick detatch bucket & palllet forks & hyd. top tilt.i paid $13,000.it has the usual dents & dings of a 6 yr. old tractor but looks like there's not a lot wrong with it.how do you think i did on the price ? 1259 hrs. not...

hello all,i have sold my iseki ts2205 & purchased what i believe to be a '62 ford 4000 4 cyl. gas tractor.lots more power,weight & room to operate.just a couple of questions.how high off the ground should i be able to lift an implement ? doesn't appear to be nearly as high as the iseki could but...

recently purchased a bigger tractor so i'll be selling my iseki ts2200 (older red model) with 1650 hrs.i'm including a 4' kingkutter bushhog,4' kingkutter box blade & a 500 lb. boom pole which are all less than 1 year old.your thoughts on a fair asking price would be appreciated.thanks,revg62

picked up a used plow for $75 from a local welder & while cleaning it up i noticed this stamped on it: 14A AO 112 with the letters HE underneath.i assume this to be the manufacturer,so i called the seller but he got it used from someone else.just wondering if anyone is familiar with this & if...

the woods rm 500-2 finish mower that came with the tractor i bought (both used) has a leaking seal on the bottom of the gearbox,bad enough that it won't hold gear oil.i've been told"just fill it with grease"...we'll in my past experience shortcuts never seem to pan out.i connected it to the...