Recent content by smokinmad

Loaded a 2012 2520 I bought, on a trailer and drove 175 miles...got home, tractor would start but as soon as I put it in a range it would die....finally got it off trailer and let it sit 30 min......tried again and it started and acted normal...have put 5 hrs on it and no issues.... Totally lost...

Wishing you the best of Luck....that was my thought also...keep tilling and you will kill all the weed seeds....that started 30yrs ago....and im still tilling like a mad man

Thank You for your help....

I bought Hoyes hydraulic adapters...1st is screwed to pressure on pump with a T....the T feeds the loader. The out line comes back to feed 3pt...and pb is the hard pipe into top of tranny.... So...I need to run the Out to the tranny and the PB to 3pt hard line.... So the Pressure flows in by the...

Get the 3pt tiller....you will find, as soon as people find out you got it....Hey, do you till gardens....30 $40 not a bad gig....I'm not greedy... I till, then take my hoe and draw a row and plant...then till another row....very few foot prints

I unhooked the pressure hose to the 3pt, it leaked out oil...then I ran a hard line behind it up the transmission for a return for the loader valve. I think the problem is the oil that leaked out..... The loader works fine... it's just the 3pt wont do anything...finger is what i removed...pipe...

Added a loader to my 276D...loader works as it should.....when hooking the plumbing up for loader, I unhooked the line to the 3pt and it spit out oil...did my plumbing job then hooked up the 3pt line....now it wont lift...my thought...not getting oil...thinking there is air in line....but...

Looking for some pics of how your 276's loader is plumbed. I got my J.D. model 75 loader mounted on my Yanmar 276. Looking for advise on doing the hydraulic plumbing.... Thanks :fiery:Smokinmad

Ok...Know this is an Old Post, but then I read it. So I am going to add in here another problem with 1210 hydrostats. To start with....you have to split tractor to SEE #5 lever, so you can't check #6, to see if nut#7 has worked off the bolt. Sometimes the pin #13 in that diagram falls out of...

Yea, I know that thread VERY WELL. I'm same name on that site also. I did that Surgery on my 1210, I'm no mechanic, but I Did It.... So why is my tractor moving.....I think I might have an idea why. That is the Drive Rod for the hydrostat drive pedal. What happens is one end strips out, so you...

ASYMAIR.....Fantastic Post....Great Job..... Glad I caught you before you "Split" her apart....Need to tell you about your hydrostat drive rod... Was mowing with my 1210, hit a log with deck and it lifted the deck up. Backed up and Did it again....lol.....Any ways, when I tried to go forwards...

Ok...had to split a Ford 1210, to put the tie rod end, back on the hydrostat drive rod. I amazed myself, you see it was my DAD that was the mechanic, Not Me. ANYWAYS, got it all put back together (no spare parts),started it up and it worked. Well atleast it did after, I beat the steering wheel...

Never thought about "Fluffing Up" the snow, before Blowing it, with a Finish Mower...LOL....Wonder if you could Win-Row that Crap.... I loved the JD green paint on the p/s unit on a orange kubota..... I was putting a model 75 loader on a JD 850, but no loader valve...went to my JD...

Found this while looking at a Pug.....The pug has hydraulic steering, so why wouldn't this work to run a cylinder to have power steering on a tractor? Yes, HOYE TRACTOR has a add-on unit, well when they can get them. No, I have not priced PUGS parts yet. Was wondering what you Tractor Guru's...

You mean kinda like this thing? No...don't remember where I saved it from. Think I would put it on a Dual bar frame, that cutter on the back bar and put 3 disk cutting blades on front bar to make your rolls This was on TBN. you might PM Madmikesmech about HIS sod cutter