Forums

Spanner's latest activity

S

Spanner reacted to Tx Jim's post in the thread JD 5101E Open Station won’t light up dash or spin over. with Good Post.

I'm unaware where RE503242 is mounted on a 5101E but on older models it's mounted in engine thermostat housing similar to photo below...

Friday at 2:20 PM
S

Spanner replied to the thread John deere 3520 very hard to start but when it does eventually runs normal.

Rather than Glow Plugs I think the 3520 has the Air Intake Heater device on top of the intake manifold, A single wire connects to the...

Friday at 2:06 PM
S

Spanner replied to the thread BCS 735 doesn't start anymore.

Phew!

Monday at 7:56 AM
S

Spanner reacted to mcfarmall's post in the thread What type of grease for angle gear on string trimmer/brushcutter? with Good Post.

I'd use a semi-fluid grease in the NLGI 00 range. Also known by some as "corn head grease." If you use a NLGI 1 or 2 grease such is...

May 15, 2022
S

Spanner reacted to mikegt4's post in the thread My loader screams at me! with Good Post.

After starting it up today (these 4 cyl. flathead Hercules engines sure start easy) I started to cycle the hydraulics and look at some...

May 15, 2022
S

Spanner reacted to JJT's post in the thread JD X300 mower deck belt with Good Post.

Your old belt was surely stretched more than an inch or two. I doubt the longer belt is the right belt. The difference between new...

May 13, 2022
S

Spanner reacted to tomplum's post in the thread JD X300 mower deck belt with Good Post.

Before you go further, Deere has a fix for this that works. Ask about 42C deck belt failure Solution 116525. This assumes that you have...

May 13, 2022
S

Spanner reacted to repete's post in the thread I need a propane torch that works with Good Post.

Self igniting is the only way to go. https://www.bernzomatic.com/Products/Hand-Torches/Instant-On-Off/TS4000T

May 12, 2022
S

Spanner reacted to tacticalturnip's post in the thread Would You Loan It Out? with Good Post.

Your neighbor is the type of guy that doesn't trim his zip ties.

May 11, 2022
S

Spanner reacted to Wagtail's post in the thread Are you "brand" person when it comes to your tractor? with Good Post.

In one way, yes, I'm 'brand loyal' as the JD products have served me well... because I was fortunate to buy the right tractor(s) for my...

May 10, 2022
S

Spanner reacted to orezok's post in the thread Groan part quatre with Good Post.

May 9, 2022
S

Spanner reacted to stuckmotor's post in the thread Pallets in fields with Good Post.

In other words a rabitat?

May 5, 2022
S

Spanner reacted to Tx Jim's post in the thread JD 1020 - Input Shaft Seal Leak with Good Post.

Welcome to TBN I can't give you any advice on seal repair in a can or bottle. If you have any mechanical ability I can give you advice...

May 4, 2022
S

Spanner reacted to mcfarmall's post in the thread Kubota backhoe cylinder fitting welds are horrific with Good Post.

The welds look fine. It's the threaded bung that's rotting away.

Apr 28, 2022
S

Spanner reacted to MikePA's post in the thread EverythingAttachments.com with Good Post.

Reminder, since it is not obvious to some, this is the Attachments forum, more specifically, the Everything.Attachments.com thread.

Apr 28, 2022

Show older items

Forums

Top