Recent content by Truautorepair000

OK so the sae kit was just a bit off for sizes. So I dug deeper. I think the shifter was bumped out of adjustment. I loosened the jam nut, then moved the shifter away from the steering wheel, and locked it in. Good as new. I can't believe I didn't think of trying this at first glance. Thanks for...

LS dealer says national back order. I ended up getting that SAE kit so I'll follow up on how it goes...

I've gone through their website and for the spherical end alone, they have like a dozen choices in m6x1.0. But i was not able to find the little slide shaft that it engages. Maybe I'm just struggling with their selection?

https://www.amazon.com/671900084-671400252-1409-3003-1409-3004-1409-3006/dp/B0CNSRBR3H/ref=asc_df_B0CNSRBR3H/?tag=hyprod-20&linkCode=df0&hvadid=693712983091&hvpos=&hvnetw=g&hvrand=15862198853936542409&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9009935&hvtargid=pla-2292987524349&p...

Hey so has anyone found an aftermarket repair for these joystick rods? My loader can't curl anymore and I see the rod and slider joint are worn. I can order through my dealer, but they are very far away. Amazon shows several kits as the three piece set, but they are 1/4" threads, so I'd have to...

I deal with scenarios just like that, in my line of work. Sometimes I come across a silver bullet and save some leg work, sometimes not so much. It's crazy how this pump looks "run-of-the-mill" compared to other tractors in its class. The downside is that the dealer doesn't stock the various...

So I'm at 170 hours. My dealer isn't super helpful, they are more of a landscape supply place and the technical questions maybe puzzle them. I'd be a buyer if there was a $500 upgrade. Nothing crazy, maybe 2cfm more. That may not seem like much, but it's close to 30% upgrade. I just really need...

I saw the deplorable diesel offering and it looks similar to what this model has. The cost is a bit steep, considering it won't be used for commercial applications. Maybe someone will chime in and say they were able to bolt up a more affordable option.

Hey, just looking to be pointed in the right direction. I have a 2021 mt122 tlb, and it's fine, as is. I use the backhoe a lot, and could benefit from more gpm from the hydraulic pump. I want the backhoe and loader to be a bit faster. The restriction could be hose diameter, or possibly limited...

I've got the same tractor and have a different bucket on the backhoe. Mine is 12" is yours the 16"? Wondering if the backhoe has enough umph for the 16" and it looks like you might have it

There has to be a way to modify the software. Im from the bosch ecu world, in my professional life, and we have several ways to modify ecu strategies, programming, adaptiona, and coding. Most common is bench top where you have a 12v power/ground and your network lines from a kwp2000, or which...

Here it is, installed. As you can see, the pin hangs out a bit, but it won't slide because of the pin locks. Everything is perfect for the ls MT122/25 series. I ordered direct from bxpanded and told them I have a JD 260b for correct fitment. Thanks to the poster above who contacted them! Time to...

Update*** I finally got to measure and order one. The measurements for my backhoe seemed to be very similar to the jd 260b so I ordered it. When it arrives, ill follow up

I just think this is odd because the engine has rubber engine mounts, designed specifically to isolate it from vibrations, and to localize its vibrations too....

Hey so I have an mt122 and I am trying to make a hydraulic pressure tester. Main reason for making one is for periodic health check and adjust. For some reason, I am not able to find the correct fitting anywhere. The quick connect fittings all say 3/8" on them but not a single 3/8" fitting i...