Search results

Unfortunately I did not take pictures when reassembling but here are a few pictures of the broken oil seal. In the Youtube link above the guy states it is a two piece seal. That maybe the case on a BX, but not on a B21. I did have to apply heat to the seal on the axle to remove it for about 10...

Can anyone explain how to adjust the rock force on the front axle of a B21. The shop manual shows the use of a spring scale and specs but not actually how to do it.

Recently I replaced all the hoses on the backhoe. While doing so I removed the Boom cylinder (the one inside the boom) to install new lines. Before reinstalling it I wanted to test the connections for leaks. I was told that I could start the tractor and test the cylinder while it was on the...

Thinking about installing one on my B21. Can anyone direct me to a thread dealing with an install on a B21? Honestly spent 4 hours with the search function and found nothing on the B21.

Can anyone tell me if this seal is removable? It does not show in the parts manual or in the shop manual. Part #60 seal would rest against it. Is part 60 a two piece seal????

I have searched for B21 specific threads about this issue but really did not find any. Mine is leaking from the right front axle after it turns down behind the wheel. Are B21 series different then others? Can anyone direct me to an thread regarding the issue on a B21? Thanks in advance.

I know there are numerous threads about choosing tractors but with so many it gets little confusing. I live on 3 1/2 gently sloped acres with a lot of rocks/boulders. The type where you find a dirt spot dig a hole and hit more rock type acres. Pretty much have all the surface rock where I want...

Well after leveling the frame. I then used a 6ft straight edge across rear of frame to use as a point to measure forward to boom supports and then to boom cross member. I知 off 1/2 inch low side of boom to rear of tractor. Measurements to supports are good. All the comp links are good except...

Re: Straightening bent TL421 Boom on my B21! I put the FEL back on the tractor and put the tractor on level stands front and back. Here are some pictures hopefully showing how bent the loader is down to the left. Picture showing a prior repair as well. Measuring across top of boom from rear...

Few months back I ran over a large rock that fell out of my bucket. Turns out it bent the hydraulic oil tank bottom. So today I straightened it. It was dented in about 3/4 of an inch at its worst spot which happened to be at the drain plug. Cleaned the tank and strainer while doing so. No...

Just a quick update. Clutch shaft, throughout bearing and spring all replaced. New bushing in flywheel, pressure plate and friction plate installed. Included a better picture of the damaged old clutch shaft.

Anybody out there have a TL421 in good shape out there? My loader was repaired by the prior owner, it’s welded wrong at the lower arm behind the bucket. Can’t be repaired because the loader appears to be tweaked.

What should I look at and test to see if anything else was damaged and needs replacing?

Splines in clutch totally gone!

Well the split is going fairly smooth. My only issue is removing the front propeller shaft. By mistake I removed the pins at both ends and cannot get it to release and drop. Also I found out that my front axle was basically bone dry. Appears I have a leaking seal on right side. I’ll address that...

B21 1,100 hrs 2007. I'm the second owner purchased it with 600 or so hrs. Today while going up slight incline machine started screeching and grinding. Putting it in neutral the noise is not as bad, put the clutch down noise is much worse. Is there a way to diagnose that it's the clutch not the...

B21 1,100 hrs 2007. I'm the second owner purchased it with 600 or so hrs. Today while going up slight incline machine started screeching and grinding. Putting it in neutral the noise is not as bad, put the clutch down noise is much worse. Is there a way to diagnose that it's the clutch not the...

Putting on new front tires on my B21 and noticed that they have tubes. Can I install tubeless tires or are tubes required? I like the benefit of using a plug kit to repair leaks like in the rear tires.

I had an issue starting the machine, realizing I had this issue in the past I knew to look at the stop solenoid. Played around with it and for some reason the tractor started again. Ran it half a day then while using it with the front bucket up it just died! I could not get it to start. I have...

I removed my backhoe for the first time and tested my PTO (not that I needed to) and when I engage the PTO lever downward I hear a click and the engine just turns off. Click sounds like it is coming from the engine compartment. Backhoe lever on right side of seat is in the PTO position. I see...

Hi everyone. Been along time since I've posted because the B21 has never given me problems starting. I searched the forum and tried everything. I changed the fuel, blew out all lines etc; I have fuel coming out of the injection pump bleed nut. When I pull the rubber lines Running to and from...

Can I run a 7' Hydraulic york rake behind a B21? If not I will cut it down to 6'? What would I need for the rear controls the rake is plumbed already. Rob

Can the TL421 loader be replaced/swapped with another Kubota model front end loader?

I have a old 25 ton Yard machine log splitter which needs a new engine. The original engine was a 6 horse G&S a friend gave me a 5 horse B&S from a lawn mower. The shaft sizes are differnet and I understand I would need to change the lovejoy coupling on both the pump and the engine. It has an...

Can anyone post a picture of a Amulet ST01-2 hydraulic thumb on a B21 with BT751 backhoe or something similar in size. I have finally lined up a friend to weld this unit(when I place the order) onto my B21 this coming May and would like to see some pictures before doing so. I will be using it...

Looking for a tooth bar for my B21 FEL. The Markham? tooth bar does not fit with a bolt on cutting edge that is on my bucket. Is there one that does or do I have to remove the cutting edge to install? Real do not want to remove the cutting edge. Rob

I'm replacing all four dust cover on my B21. They are all torn. Been that way since I bought the machine used. My question is do you fill them with grease or is it a dry joint? Could not really tell if they ever had grease in them. The ball joint is still tight on the lower three so far. So do I...

I need detialed directions to hook up a Amulet ST01-2 thumb for my B21. I know there are two maybe three options for the hydraulic system. Can anyone explain each with detial and the benifets to each. I will be doing the work myself except for the welding. Also can you direct me to certian...

Please compare these two machines; 2007 B21 825 hrs comes from a rental yard for $15,000 no problems, well maintained 12" bucket. 2002 L35 one owner 750 hrs for $18,000 comes with 16" or 18" bucket, 3 hooks on frt bucket ,pallet forks pto never used, never add work needed all manuals...

Found a used 2007 B21 with 856hrs on it in New York what is a good price to pay for it? The seller is asking $15,000. Also can you put a thumb Hydrulic or mechanical on it? Any known manufactures problems for that year? Thanks in advance!:cool:

How does a 2005 GL3130 with 215hrs LA723 FEL and BH90 for 23,000 compare to a new B26 with Hydrulic thumb for 28,700? I need info fast guys!

How does a 2005 GL3130 with 215hrs LA723 FEL and BH90 for 23,000 compare to a new B26 with Hydrulic thumb for 28,700? I need info fast guys!

Although I've been surfing this site on and off this is my first post. So I guess I'm new here. Hi ALL! First alittle back round. I live in Putnam county NY and pretty much live on 4 acres of ROCK. I have about 30,000 square feet of lawn the rest is wooded surrounded by old 4ft high stone...