Search results

Go away when it warms up the oil that is 🚜

Leave your shear bolt a little loose use a stover nut or double up nuts Will bend but not break right away anyway. Tightening them down makes them pop

**** my bro in-law cannot even start his lawnmower If the tv could Mow he'd let it Mine kicks me also but fires up

Your on you way to greatness My grandson can't keep my running either

They are just not built very heavily compared to a industrial loader We Sold them to dairies for Pushing manure and loading feed They flex a lot Once the industrials came Out with 4x4 they went that way Still broke em but took longer If you are Looking to move a lot of dirt and material A...

I believe it was mf 246 loader On those Check with salvage places or auction houses Have seen a couple Or just find a good industrial loader and weld away The agriculture loaders are pretty weak Has a radial piston hydraulic pump so you have plenty of oil to run it If it is working properly

On the bigger bushhogs bat wings the new pans come with a weldable Hex sleeve for blades Part number 50076706 sleeve Bolt kit is 50076475 Bush hog part numbers

Heat only a factor if one piece of the pie is doing it Hydraulics in the desert run 220 Or more that's with coolers

Yes

There is no such thing as free or government money It all Comes From taxpayers Who work not welfare or people on disability If he is forgiving the debt just means they are going to take more money from working class In ca there are more people not working than working And it keeps getting...

Without flow meter Or gauges it's just parts replacing

Governor is working and giving you the fuel to Let you do Your job

My tractor smoked a lot but I talked it into quitting it breathe better now 🤣🤯

What did radius look Like on journals if they are not tapered when cut or ground will create a shear point and snap We had a machine do a few cranks for us years ago all of them broke

Yes

When you replaced pump did you put coupler back on it is on shaft out of gear drive on back of trans connects shaft to pinion assemble

My power goes out to much for tank less hate cold showers Gas stays on no matter just a thought

Need more information do handles wobble around Did you take shift cover off Does tractor move at all Did you put drive coupler back in with cutter pin, put in backwards will fall off 😉🚜

3m weather stripping Adhesive sets up nice and hard also

Try some heat warm things up

Don't miss the white stuff Good luck

The only other thing I have done is Find an aftermarket seal if possible sometimes they are a tighter fit Or go back to kubota and see what's up. if you use any type of sealant area must super clean and must sit 24 hours for complete Also check and see how much in and out play is on shaft...

Look at your housing make sure you did not push it open or crack it with when you ruined seal

Don't know where you live We have a place here called cutting edge supply make you any size blade I want

you can order a cutting edge made for your bucket Bolts are like plow bolts recessed in blade

I have 360 hours on my tractor Took twelve years changed filters once were clean always has additive for fuel. starts and runs even after months of sitting battery is maintained one battery in that time also don't put in bad stuff don't have bad stuff happen Also has been in a garage it's...

Did you ever get this thing working

If pump is inside they both suck off same screen in trans Does your loader have front mounted pump off crank pulley or do hoses come from top cover And you have to put it in constant pump The issue would be the same on loader no oil so full of air

If injectors were bleeding off thing would hammer trying to start, to get rid of raw fuel in the cylinder makes Noise bends rods

do you have pressure

Is the pump working sounds more like no oil

For weed abatement I make a skid plate front to back covers oil pan fuel tank and lines and hydraulic filters Let Me know if you need a pic usually two pieces on big tractors

Do the loader and three point run off same pump If it has internal pump for three point should be a little cover on bottom of differential the screen for the pump is accessible under that cover if it gets plugged up enough Three point will raise at idle but when you rev it creates a vacuum...

Control valve in pump could be sticking or linkage in cover is binding you can pull side cover and and move linkage to see if control valve is working and then see if you can manually move it Buy a repair manual on eBay or wherever you find one give you better picture of the system pretty...

There are no circuit relief valves in compact or most ag equipment So when you go over the rated pressure of the system something will give way

The one lever is not sitting on the roller pry spring back and see if You can get it back on The quadrant assembly should have two rollers one is for draft other is for position control have seen them rust off also then you can repair it or find good used one Most that are that old usuallly...

What engine is in it 203 Perkins or is it a English tractor If it is a 203 only timing is on front gears injection pump has dowel for gear and has slots for a little turning

50ds had opposing swing cylinders

Yes been using For mainly diesel for a long long long time Cleared up many a fuel issue Plus keeps my gas pumps and equipment always ready to fire up

Do you put fuel additive in it when it sits? I put Techron in all my vehicles gas or diesel. Keeps them fresh

Had a old jd 3020 even minus 20 started and ran fine Only thing that would start after -30

Squishy ear plugs and noise cancelling headphones Party on

You might have already pointed to the key of the switch problem

Leave the fill screw out or loose till you pump it up and let it go down all the way it should be able to vent also

Call this place Meyer ward tractor Have a bunch of used stuff (559) 824-0558

Can always do it the old fashioned way and write it down 😉🚜

I have a new clutch disc and pressure plate for sale for a m9000 Kubota

Well I will be dumbass with you 🤣🚜

Spiders will be zinging Had a couple customers turn their spider gears into metal shavings doing that takes awhile But makes me Money.

do you feel both stages of the pedal if you do then more than likely pto disc is stuck to plate So you can see if you can hold pedal down and get a skinny blade in there but it will be tough Or you can find a heavy load with the pto and hold clutch might break free or go boom have seen both...

ATF for cold weather Works great Works good in summer to Used in the desert kept valves from sticking when it was 120 outside

Sorry 1/2 inch wrenches

Pictures

I used to just get new balls and weld them on. Make a template before cutting them off so you get the same length

Can get to bolts from inspection plate

Deja vu

Dual stage clutch is adjusted underneath Are three bolts that have locknuts on them usually adjust them to 80 thousands or 60 whichever works better take bottom inspection cover off need a flashlight and couple Of skinny 9/16 wrenches have to spin engine over with screwdriver to get to all three...

Dual stage clutch is adjusted underneath Are three bolts that have locknuts on them usually adjust them to 80 thousands or 60 whichever works better take bottom inspection cover off need a flashlight and couple Of skinny 9/16 wrenches Adjust free travel on pedal first Use a bar to hold shaft...

Did anyone put it on the locator for you Meyer ward tractor supply california 559-824-0558

So I should not drink next to the fo Fire either dammit

If it’s that bad pull the covers Clean and inspect everything You can make New gaskets or if your are careful save old Ones

sold

At the dealer Once tow company tried to haul a old mf 698 on a car Trailer a hundred miles To us Ended sending his lowboy out to get Tractor and trailer Came In yard with tractor Still On car trailer my boss says what idiot tried that and the guy said me We laughed pretty hard in a oh ****...

Lmao

Where you think all those videos come from 😉🚜

Hydraulic pto This a late 70s early eighties right Anyway spring and Ball Detent on inside,been awhile since I fixed one but pretty sure you have to pull top cover to get side cover off has the hydraulic lines hooked to it if ball has fallen out it will usually end up in little cover for pump...

My boss had a bush hog that was not cutting right on center was Putting wrong blades on they were backwards

I had a toy tractor once I would roll It down the hill just to see how fast the wheels would take it but it was tiring walking back up the hill. So I took it to my uncle and he used for book end

The Newer Perkins to me with electric shut off self bleed thru inj pump. The lift pump does have a screen in it some are in the top if it has a single screw others are on intake line pull line then take out fitting small screen there. If there is no shut off someone took it out they came with...

Do you have front cover off

Back on the farm when it got below -20 we Would start a small fire under em Cows were happy they got fed 😉🚜

When I put axle bushings in the dozers we used liquid nitrogen It was like chemistry class all ov again 🤙

Get some fuel conditioner I use Techron put in my gassers and diesels

Does it snap wheel or inside is it Held on by a nut snap ring Does it have a front diff lock ?

depending on valve you can pull spool out take of spring assembly and remove balls What type of valve is it make etc Does it have a spring action or is it detent both ways some have no springs for center just detent Others are just detent one way For a float position Does it kick out with...

Put manual gauges in and make the rest buy some wire a small fuse box if you want to mount it somewhere accessible not that much to the harness

Rattlesnakes they don’t need to know you defanged them Just saying 😉👍

https://www.tractorpartsasap.com/distributor-drive-shaft-new-massey-ferguson-180163.html

Ok sent you message

https://www.ebay.com/itm/175134369355?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=xw74eB0lRv-&sssrc=4429486&ssuid=Dc-RWYuZSOW&var=&widget_ver=artemis&media=COPY Let me know if this comes threw For you is on ebay I can check a guy I know for the engine Let me know what kind of $$ you can afford

10 dollar an hour guys or gals Plus a little trick is to try and tighten them first then loosen old plumber showed me The trick

Does the Arm have a key way Key can be good but arm could be worn Put on ground and a steer it not running and look at arm and see if it moves but tire does not check both sides

did you lift Front end off the ground and try moving stuff around with a bar safety first of course jacksrands are mechanics friend or a huge flat log 😉🚜

If it’s already broke how much worse can you make it There is so much information online And e books available buy one read up on it and tear it apart A good mechanic never says can’t Just bad engineers

If you do this for a living And really want something that works FLEXXAIRE fans Are great they use them at dump site on heavy equipment And I have put them on weed abatement tractors saved them time and money You still need to do a good cleaning once in awhile

Electric or manual shut off Manual make sure it is moving full travel try some Techron in fuel Cleans up sticky stuff in pump and injectors

💨

My wife says I have a metal allergy because I can t quit buying tools 😉🚜

On the heavy equipment when it bent we would bend it back straight and weld up anything that cracked Do this for many units over the years no problems with any of them

So it does not have a hydraulic steering valve If it is worm gear with a center steering diverter valve one steering cylinder or two Need More info or pics

most seal and sealing rings and clutches can be bought at a transmission shop Just don’t use paper clutches

Meyer ward tractor in riverdale california 559-867-0818

Did you find the problem?

All Sounds good and very ingenious But I work with das so have to make it more full proof They have dewalt blowers in cab also but will just call Me when starts to overheat Or drop It off at the house I blow it out and have them come get it Good help is hard to find out here Want to get...

They cost around 5k But in ca where it is drier than a popcorn fart and just as hot. over the years save a lot of money And repairs I charge about 1200 for install which are pretty easy don’t need a lot of pressure to turn blades and just a little wiring Had to reengineer the wheel for the...

Hours of what He has 2000 hours on first one 1900 hundred on second About 500 hundred on wacker The fan is in regular mode then every twenty minutes it reverses for about thirty seconds

Cut a fifty gallon drum run a rod threw it for 3point of course a little beefing up maybe required then put Dirt sand or cement in it when just running loader made mine with cement

With no seals on piston putting down pressure loader would leak Because rod oil Would be displaced in head where there is no oil

Just buy from caterpillar then you know you over spent 🤣🚜

That’s amazing but it would leak up 😉🚜

Leave a plastic plug somewhere?😉

Run auxillary Fuel direct To fuel pump see what happens. does it sit for Prolonged periods? Listen to injectors. Do they sound the same. At Idle have you cracked injector Lines to see if engine does same on all. governor could be sticking Put some Techron in fuel Let idle at 1500 for an hour...

easy check on oil change pull Plug silver oil you got issues My weed abatement guy puts 500 miles on his kubotas every year Put in synthetic oil and lost me a lot of money But he is happier

Check your money supply and look into a ad3.152 Perkins engine Same stuff, less stuff to fix Keep fuel fresh run forever All the bolt holes the same made many change overs for dairymen. Back when parts were cheap Plus the diesel parts are everywhere Good luck

No worries grew up on that equipment so should have enough brain power to help you Can tee into a bucket line coming from loader valve number ten jic Just get adapters for hose and gauges make a Xmas list Unless someone changed it they used a mf 32 loader if it is original

Hydraulic shop nearby? Some dealers carry them too $$$ If I remember is 3/8 pipe but you can pull plug with controls lowered So no residual pressure on it. Then you will know for sure. Amazon sells gauges, liquid filled are best. also I like a hose 24 inches long or so for wiggle room Gauges...

Nice you the man and thanks for your service also just like to fix things also like you body not working the way I want Farm machinery was the best Weld Stuff back together with different parts and engines and run it till it broke again loved working on the farm never had any money but life...

Do you guys work in government Just asking for a friend

I drip Under pressure also Just saying

You can pull plug by standpipe cover if have a pressure gauge Is pipe thread. Pressure was 2500 Psi if you pull right side cover will be able to see if it blowing off or half broken off can change it thru cover also Depending on cover might have to pull rolling pin out of control valve On...

Pretty sure you don’t have to pull trans to do front input shaft seals And if you have pto rear hydraulic pump will come out top after top cover removal Also before pulling pump check standpipe orings and relief valve notorious weak spots Piston seals on top cover can be bad also I worked on...

I like the old fashioned way pry bar blocks and a sledgehammer Of course dad always said I had more muscle than brains Makes for a good work out though 🤣🤙🚜

Old Wagner loaders were Displacement cylinders just a snap ring on end to keep from shooting out gland 🤣🤯

I’m great post simple magic My little kubota leaks down all cylinders are fresh but valves are **** has load checks too I have maybe seen two loader backhoes that would still be up over night and that’s in 45 years of working on em Why you think they put all those safety locks on em 🤣🤣🚜

I live so cal drive to la for ten years same problem with my finger

I am to old now one chance is it

People that ask a question on how to Fix something or How to do it then say that’s not it That’s why I wear this hat

On the super old backhoes used to use heat and porta power with atf sometimes even got a good fire show

Yes if a diesel is running lean can cause some overheating

All manufactures have different specs for hydraulics my little kubota is 2000 My 30b is 2500 My terex bh is 3150 Will a dual pump and with a kick out valve at 2900 to save fuel Nothing is set in stone

Yes it does relieve the pressure but say it set at 2000 and you set it to 2500 say you have a three inch cylinder how much more force are you now exerting on a piece of equipment that was meant for 2000 Most relief are adjustable with shims inside or screws some are even inverted where you take...

This is actually a hydraulic fan that goes from suck to blow or Vice versa depending on application It’s a FLEXXAIRE fan out of Canada Really great customer support This one is on a wacker nueson st40 has a built in timer so every twenty minutes it reverses and blows or sucks. works really...

I have mid mount Mower was on my kubota bx2200 60 inch Live Southern California still works used this spring on neighbors yard Just collecting dust

Those things were dinosaurs just big and heavy and pretty much dug anything simple also

Mine is 2015 I also put on a oil cooler around 120000 tenpin summer was always around 200 or more so I pulled temp valve and plugged it off now stays stays around 130 Sumer still gets to about 170 in traffic but soon as we roll drops back down heat kills

Don’t know max psi but over usually means catastrophic failures down the road cylinders leak booms crack welds break pins and bushings wear faster valves leak Have seen guys bend dipper rods I turned them up for years and told them it’s just more money in my pocket

Mine has 200k changed oil and filters regularly and almost lost all the oil on a bonehead line change Still works good and has been carrying my tools for five years I also put lubeguard in it shifts a lot better with it Also have a 4l60e with 200k Plus wife says I have a lead foot Y’all have...

Is fuel fresh and do you use additives to keep It fresh

Is pump sound is pump cavitating Air will give mushy hydraulics Plus is he Hitting big bumps so linkage bounces slow lift response can also mean weak flow or pressure Start with basics don’t jump off the cliff till you have checked simple stuff first

Path of least Resistance no Matter what is leaking it will still leak valving Is not 100 percent so it will leak load check valve circuit relief valve All Leak to some degree All my cats leaked down terex masseys kubotas if it doesn’t you are few and far in between On warranty they actually...

So if a seal Is blown it will displace Oil from one side of cylinder to other also unless you hydraulic locking mechanism plus in forty five years don’t see to many valves that are totally leak proof Reason for hydraulic locks on cylinders Be pretty scary if you were a hundred feet in the air...

First name Is dante And I will brag I was the best mf mechanic for 25 years so the customers just called me dman

The other thing loader valves have is a load Check it keeps the oil from leaking back thru so you don’t get the fall when you first crack it Takes so much pressure to lift poppet off it seat then the pressure is more on lifting side so bucket or loader does not fall first

I think you answered Your own question have a great day

Spray and tap it with hammer either orings or sealing rings Wd40 is **** use penetrate

They have passive regen like all those poses so higher rpm’s mean less problems in theory of course That’s what it is based on

I use wd 40 to clean my tools dries quick and goes away 🤣💪🏼

Easy check for cylinders loader all the way down do this cold and put down pressure so relief goes off for a minute or two at intervals and then touch cylinder where Piston is if oil is bypassing will be warm to touch Also can do same thing pull off hose cap it and see if oil shoots out same...

Look in your bathroom closet a big towel works for me Wife gets pissed but I just get her some cold stone and she is good

Rule of thumb on most cylinders level is half way for rear hydraulics Always set up my equipment that way. Then you have same tilt forward as back. same with side tilt if you use double tilt well you get the whole stroke I am coming from an operator point of view and have set up hundreds of...

Battery quick disconnect can put it where you want just put a 100 amp circuit breaker for safety

The other thing about cast is if you keep Heating it it will actually shrink So once you heat you need to hit it or figure out a press to work on it I have shrunk quite a few castings so pin would fit tighter

Did but never had one barely had money for shoes back then me And my buds seemed to always get them running of course you’d all laugh now but no money means being smart and creative

Control valve in cover or slow fast valve is turned

Get some phone wire mark hoses to fittings go get them Made cheaper in the long run

Damn that’s a lot of money How much a good used or rebuilt engine maybe shop around Sounds crazy I overhauled some cat And Cummins that were less than that

Keep beating then that’s what I always say

Pull top cover relief valve blows up sometimes if older style also that way you can see of cover is ok Just pull bolts around outside And also pull standpipe cover and stand pipe you can check it first sometimes orings blow have seen standpipes broken also How much play is on bushings of lift...

Yea no

Broco rod just need some Oxygen and battery Working on dozers don’t leave home without it

Friends dad when we were In High school got caught in the pto that’s why those plastic guards are on there

First off is this a Massey fergusen 240 And are you talking rear hydralics Because they run off a internal Pump

Injectors meter the fuel so did you have them sent out so they would dump more fuel?

Good tapping oil and a soft hand and never break another also I use a torch for taps hard metal blows out quickly

Guess I must be old never used

It’s a free Country well sort of So far you can still do what you want. In ca you can steal and not go To jail or serve anytime So if he wants to turn all his safety equipment off it’s his do as he wants I used to jump Off my roof and I don’t wear a helmet riding my bike Plus sometimes I...

Find a real Mechanic to fix it do you have blow by pull the dipstick if oil shoots out problems aslo pull muffler off see if you still have smoke old muffler full Of oil will make really good smoke Yes injectors could be a problem You can listen to them or crack line one at a time to see if...

It is a diverted valve take it apart and see what came apart

Go to gym for a month won’t be as heavy 🤣🚜

More info what tractor Usually they have a tool if no tool some have measurements if all else fails make sure they are all the same height Some also have inside measurement where set screws touch plate

Can always put a quick drain plug in just pull lever Had them all our fire trucks at the city made Services easier of course the oil filters still got me sometimes

Why so much grease Only takes a squeeze or two wipe off nipple before and after and make sure loader or backhoe is in position so grease goes in pressure side Just like front axle pivot needs To be off ground so grease gets where pressure is

Why not just run from quick couplers for backhoe in and out

Make your own and if you need gauge cluster can buy em on eBay

Brrrr

Replace cables go big or go home I use welding cable finer wire carries more load efficiently then fix hard starting

Mf 240 what buttons

I have overhauled literally thousands of engines never had one belch oil out exhaust Perkins cat Cummins ford kubota duetz guy either soaked them in engine oil which I never do or he put it together with the block looking like in picture then what you have is failure to communicate

They are not synchro have to stop to shift or match engine speed with trans I put synthetic in everything I own. repairs cost way more that oil I had 10k hours on tractor no leaks or repairs on transmission or brakes

if it is a clutch tractor put it in higher gear and give it. A pull Might blow something up might not I have seen clutches blow and material get trapped between flywheel and block Also drop engine oil if. Bearing did seize going to have metallic looking oil

Look for older mf four wheel drive cab tractor like a or similar 390 were nice and easy to work on just like your 255 They had plenty of power also The new **** is good but a pain in the ass when you have any problem at all And then finding someone who actually knows how to fix it well There...

I really like that I have done that several times I paint it afterward and use it for yard art

Why would someone tighten the filter that much?

They are not that hard to do gland spins on or has wire that holds sometimes need a spanner wrench Just look at it be careful though some have little set screws to hold it but pretty basic stuff And if you have a good oring seal place nearby can get you all the parts Or get kit from dealer...

If they are both pipe need soMe Teflon tape for the threads

If the fuel has been crap everything is stuck inside pump can try putting Techron in it and let run awhile But if it has been that way awhile need pull cover and try And clean it up or send out pump Unless you have a linkage problem Is it manual kill or does it have solenoid looks like old...

It’s just another name For a China virus

I have had guys put t on those nice pretty welds

Those gauge cluster are **** wiring is most always hard and crumbly Tac runs off cable Can buy cluster on eBay

More than likely front seal On injection pump is leaking You can do it

So if you buy new and it is 1k And new aluminum built one is 2k but probably won’t go bad as long as you keep everything cheeky hmmm

Waste of money if you did not add conditioners let me know if you use it. I love money and love cheap ass old fuel . Last customer who was using crap like that I got 6500$ Mechanics in area will love you

Warranty will usually cover that if it is new sometimes they have a charge for road calls but if you just bought they should handle whole thing

Overhauled literally thousands of engines never had one smoke like that have had bad sleeves and piston rings aftermarket ****. Oil pressure bad oil pump or relief valve in pump or to Much clearance in bearings Did they cross hatch after boring Are there seal on valve guides My break in was...

Does it start when you jump starter Seriously some systems need 12 volts at starter solenoid do you have that with key if it starts everytime jumping it check voltage from key and all neutral start switches a safety switch with corrosion or high resistance can make something not work properly

If It is leaking at injector where line goes in take off clean it up put on tight enough you can still spin abut and walk it back and forth to seat reassemble and see what happens fixed many that way in field when work had to be done.

Not near enough information Is oil cloudy after using. Is it milky before using how long since service Did he run a flow check on pump Is pump getting warm right away Does it whine? Give more details

That’s some funny **** there Thanks for making my day

if the grease zerk was plugged take them out clean out hole and insert new zerk not jump on grease gun Just saying

Still have my bx2200 One like it is over 20k yea no

Way not enough info Tractor age six volt twelve volt Binary non-binary trans no trans

Lack of Oil make You crazy

Pull drain plugs silver and chunks of metal bad

When we bought a new tractor on the farm we hooked it to disc plow or whatever and worked it ten twelve hours

Buy bigger pay more for repairs

It’s like what you want I have top, tilt and scraper hyds. I never get off the seat😉🚜 everything is smoother adjust on the go and keep on rolling

Well first of all if you are leaking oil fix it Second check shafts for play usually a reason seals leak Third instead of shear pin, clutches work better can pick up aftermarket drivelines with them on already, cut to fit Bareco is the company I go with I can buy a new driveline cheaper that...

The governor is speed driven balls sling Out as it speeds up so pushes carb linkage back So as engine speed slows governor opens throttle back up so If governor is working and it stalls out you need to shift to a lower gear or you running Out of gas.take off carb clean out jets check float...

Solenoids are in bell housing has relay box under dash assembly What is stall speed What color is oil does smell burnt Could be clutches or torque converter also make sure brakes are not to tight and roll easily