Search results

Again this is for the Mitsubishi SL3/SL4 motor with Bosch injection, but the solenoid layout seems similar to what you have. Hope it helps

I have a Mahindra with a Mitsubishi motor and the solenoid looks very similar. On mine the solenoid pulls in when you turn the key to engage the starter, then de energizes and the hold circuit energizes when the key is released to the run position. Attached is a wiring schematic of it. The ETR...

By the way the real reason I like my Woodmaxx is the shipping container makes an awesome work table

This is for the smaller Max tractors, would think the 28 would be close.

When I was trying to figure out what was going on I came across the service manual for the Mitsubishi SL3 motor which is what's installed in my tractor and a number of other Mahindra models and thought I'd share a couple pages on the procedure for installing the stop solenoid and a couple of...

Used the tractor yesterday everything was fine. It's a Max 22 Went to start it this morning and it cranked with some white smoke coming out the exhaust, but wouldn't start. Cracked the fuel lines at the injectors and basically dry. Just to be on the safe side, replaced the fuel and air filter...

My new Woodmaxx FM 54 mower was delivered last week and after setting it up and putting in a couple hours cutting the lawn and some brush I thought I'd share what I've learned. Let me start by saying that I did a lot of research including reading the very long Flail Mower thread and couldn't...

I tried to get the information i needed from the +500 page flail mower thread in the attachment forum, then talked to a couple of suppliers and ended up being more uncertain then when I started looking into them. Bottom line is I'm wondering if anyone has any operating experience running a 48"...

Changed the fluid last week and was originally going to go with the Chevron 1000thf but turns out the nearest source is in Gardner, MA about 60 miles away, so ended up going to the dealer. When they told me $110 for 5 gallons I was a little floored because I checked a few places on line and saw...

Changed my hst fluid a few days ago on my Max22. There are 3 drain plugs. Two of them are on the bottom of each side of the tranny near where the axle tubes attach and the third is on the back side of the mid PTO. I couldn稚 figure out any way to remove the one on the PTO without taking off the...

Getting ready to do the 200 hour hst/hydraulic fluid change on my Max22 Going with Chevron THF1000. I looked at the parts list and it shows the there are M12 seal washers on the 3 drain plugs. Does anyone know if these are reusable or are they like a crush washer that needs to be replaced ?

If it was the rear PTO that's probably what I'd do. It's pretty straight forward. This is the mid PTO which hangs down below the transmission. Access kind of stinks. So I assume I need to drain the fluid. The seal is like the rear PTO so that seems like a pretty typical replacement. From the...

I have a 2 year old Max 22 with about 170 hours on it. It's leaking hyd fluid from what looks like the mid pto shaft seal. Stopped by my dealer to ask if it was covered by the 5 year power train warranty. The dealer contacted Mahindra who denied the warranty saying it's an external seal. Was...

Was out cutting the lawn and decided to snap a picture of the mid PTO location. The picture is from in front of the rear axle facing towards the rear. Hope it helps.

Was doing some maintenance on my tractor (about 150 hrs on it) and was going to check the torque on the bolts. It's a Max with FEL and Backhoe. Noticed that all of the bolts for the FEL and Backhoe are ISO metric or SAE and the manuals for these have recommended torque values and torque charts...

Thinking about adding SSQA on my Max22 which has a ML202 loader on it. Found a company called Worksaver that has a pin on adapter for the Max ML24 and ML26 loader that weighs only 85lbs. Was wondering if anyone knows if the pin spacing and size is the same on the ML24 and ML202 loader.

I think this is what you are looking for. I have a Max 22. The top and right bottom links are adjustable. Also note the bottom of the lower links are offset at an angle.

Was getting getting ready to do my 100 hour maintenance and popped the hood to look things over. Noticed that the oil filter still had yellow overspray paint on it from paint they put on the dipstick. See the photo. Thought this was odd since I had the dealer perform the 50 hr service and the...

I have a 2 year old Max 22 with about 150 hrs on it that has really not had any problems. I have gone to the dealer a couple of times with minor issues and questions and for the most part they've been very good as long as they don't need support from Mahindra. The latest issue is the FEL will...