Search results

I had to change the drive belt on this mower, which i have done several times and always mark how the clutch was to be put back on. However, this time something has gone wrong and I do not know what. The mower will not crank as always with the PTO engaged so i dont think its gone bad. I need...

I REPLACED THE IDLER ARM ON MY LT 1042 MODEL 13BX11CG710. I LOOKED ONLINE TO GET PIC OF WHERE SPRING RE-ATTACHES, BUT ITS NOT CLEAR. THIS IS A 2005 YEAR MODEL. WOULD ANYONE TELL ME OR SEND ME A DETAILED PIC OF HOW IT HOOKS UP.IT HAS A KOHLER 15 HSP. THANKS IN ADVANCE

I need a complete overview of how to replace the idler arm on a 2005 cub LT 1042. the parts diagram really doesn't show a good picture. i understand there are several different arms for this model. Mine is a 2005 model 13BXCG710. if anyone can send a good pic it would be greatly appreciated...

I am at the end of my rope with the belts breaking or burning into. I ahve checked pulleys, try to level deck and yes, they are put on according to diagram. I have had this mower for 7 yrs and always replaced belts myself. This is the 5th belt replaced this season! Getting a little heavy on the...

Does anyone know the routing for the drive belt? or where I might find the diagram? Thanks

Does anyone know the gauge wire to wire up the clutch? Got a broke one.

Replaced both idler pulleys, bought new belt in about 1 hour of mowing belt came off again as before I replaced pulleys. This has been happening a lot and costing money. Can anyone give advice on what needs to be fixed. Thanks in advance

On a 19 horse Briggs & Stratton, I need to know PRECISELY what the air gap is to be on the clutch. this motor is on a Cadet Tank and after a few rounds the clutch just stops, so I turn it off a few min. and back on and the same thing.It even will stop when there is very little (short) grassy...

I just had my original motor replaced, a kawasaki 19 hsp, with a 21 hsp. Briggs,OHV. It worked fine for a while but I cannot figure out what is happenig, Something is pulling new batteries down and causing clutch to stall . I replaced battery twice within a month and works for a mowing or two...

Well, I adjusted the air gap to .010 on clutch. It ran for abour 30 min. and stopped. I shut it off for 30 min and would not start I had to jump it off. This is the second new battery in ONE month. This is a 21 hp Briggs motor. Please let me know what gap it really should be and do you...

Commercial Tank M48, when mowing for a while pto gets weak and stops. I have changed battery's and will work again for awhile, then the same happens. Bought a brand new battery, and after about 3 hours, started doing the same thing. I feel like it may be in the electrcal part of something on the...

I also own a Cub Commercial Tank M48 2005 model year, and just got out of shop yeaterday because govenor went bad. Mowed for about an hour and I did notice that when mowing in, not so tall grass that it seemed to stall. There are new blades on deck. So finally, it did stop. I checked belts and...

cub deck seems to mow uneven on one side. It seems to cut closer than other side.I have taken deck off checked cables under frame, replace deck and measured and level from top to bottom and side to side, and seems to be close to level. measured from bottom of blade to concrete surface and got...

I replace drive belt and reinstalled clutch and now when i engage pto it blows a fuse and cuts mower off. Clutch seemed to go back on without trouble. What is the problem. I need help quickly. I need to mow or just get some goats to take care of my yard.lol please help me, getting frustrated!

Need help on replacing drive belt and the routing of the belt. Has a total of 5 pulley'sfor belt to go around. I know you experts have an easy way of doing this! Thanks in advance:)

Now when I mow and lower deck gauge to lowest position the belt comes off after a short time. However, when I mow in position up from lowest it will not come off. I did notice that the idler pulley has a dip around the top edge, possibly that is what is going on. I know there is someone out...

I replaced the fuel lines on this weed eater due to ethenol gas eating out the lines. Once replaced, I can can get fuel to the primer bubble, but it will not start. Any thoughts on what Imay have done wrong?:) Thanks in advance

can someone please tell me how to attach the deck lift pins,(looks like a question mark bolt with spring and pin) attaches. Thanks in advance:)

I have a 2005 LT1042 and the spring to the deck broke and came off however,I cannot figure out where the new spring attaches to the arm. I would like to see a picture of the deck where it goes or simple instructions. Thanks

Hello, new to this forum! I only use Cadet equipment and have great experiences with them for years. however, lately it seems the newer models tend to give more problems than the older models. I need a vivid picture of where the tension springs attaches to the deck idler arm. Mine broke and I...