Search results

Like to sell this mower. I was wanting to restore It. Never have time with other things going on. Has good tires, new battery. Clean carb and bowl gasket. Has good deck. Runs, deck lift works, PTO works.

Anybody on the forum interested in buying an old Jacobsen GT 16 to restore? Its about 45 years old . Has Kohler engine. I have it running and like to get it out of my shed. Has fairly new tires and new battery. I was going to restore it but have too many other projects.

Anybody know anything about these? My buddy told me to put one on my 96 NewHolland 3930. The lever that switches from front to rear hydraulic has to be tied with bungee cord for FEL. He said it would fix it. Got one off Ebay and it dont look like it will come close to fitting my tractor. The...

Have and old 12' stock trailer with old style 2"Bulldog sliding collar hitch. Just noticed today the pin in front that the jaws swivel open on are worn bad. The pin is not even connected into the top half. Is there anyway to drill the pin out from the bottom and weld in a new pin? It will be...

My tractor is about a 96. It has the hydo selector valve under the seat. It switches from rear lift to the front end loader. It jumps out of position for the loader. I use bungee cord to hold it. Isnt there a plate or adapter that bolts on to allow both front and rear to work without switching...

I have been asking a lot of people about converting this Bush Hog loader to quick change. My neighbor help me with this. We used all the scrap metal around here and what we could find. We burned the brackets off the loader and welded plates on the bottom of them. Had to saw pins off the hay...

Has anyone changed their pin on Bush Hog bucket to John Deere pin on type? I was studying getting on of those Titan weld on plates with top hooks and pins. This loader is wider than a John Deere where its suppose to connect. I'm afraid my loader brackets when I redo them will be in the way of...

Got a 3930 NH with a 2345QT loader. Anyone redone theirs for quick change Skid Steer or John Deere pin type? I do know JD loader cylinders arms are not same distance apart as BH. I seen the hooks, plate and pins you can buy to weld on bucket. Curious best way to make bracket that will stay on...

Not sure this photos will show up. They are photos of my old clutch and a new one I ordered. The new one part number is on the box. The old clutch had the inner tension springs or whatever you call them. They are same spline and diameter. The new one just didn't have the springs. Went ahead and...

What is best way to convert an older 4 pin bucket loader to a quick attach loader. Seen one made by WR Long. They are rather expensive. This is a Bushhog brand loader on 3930 NH.

I have a question about the PTO on a 3930 New Holland. The PTO has an electric engage switch. The PTO will continue to turn while engaged with clutch depressed. Is it suppose to stop with clutch in? I've been using it since I bought it two years ago like this. My John Deere and Massy friends say...

In process of changing clutch-pressure plate. Found new pressure plate and clutch on EBay. Like to ask some of you mechanics if you replace pilot bearing and throwout bearing if they are still good? The original is Koyo made in Japan. I'm worried about putting in Chinese replacement bearing. New...

Bought one of those air water adapter kits today. What is the best way to get fluid in the rear tires and about how much will a 3930 NH hold? Seen several ways on You Tube to do it. I have portable air tank and 18 gallon 12 volt spray tanks. Will that work to pump it in?

Anybody ever had a fuel shut-off valve under the tank leak? The parts diagram shows an o ring. On the hydraulic shifter under the seat is there anyway to adjust it to keep it from jumping out of position? It switches the hydraulics from the bucket to the rear lift. I have to use a bungee cord to...

Someone ask me about these on a private message. Could not post a picture there so trying it here. This is a Neura Trailer SKU-08-601 spring. it's 1.5 coil 13.63 long cost $15.82. I used a chain to find the proper tension points using temporary clamps on attachment points. This has worked well...

My neighbor has one of those old 274's. I believe Nissan made the motors for them. He has not been able to find a hydraulic pump anywhere. They may be made with aluminum housings and rebuild places won't mess with them. Anybody here got any info?

Just want to share what I have encountered in the last few weeks. Bought a 3930 lows hours but tach cable was broke. Didn't know a few things till after I bought it. When you buy a tractor run it long enough to see if hour meter is working. Ask a bunch of questions cause some people won't tell...

Just bought a New Holland 3930. It's missing or broken the hood hinge (R.S.) part that goes on the tractor. Since it's gone I have no idea what it looks like. Can someone send a picture of them and tell where I could find some.?

Found a 1165 Massey 4 wheel drive 400 hours. Owner says it will go forward and reverse like it should. Sometime if you push the pedal it won't go. Anybody know what the problem might be and how much it would cost to fix? Says he hasn't took to a dealer.

I have a Jacobsen GT 16 . It still runs. I intended to restore this mower but got too much other stuff going on. It has a good deck. Put new tires on it a few years ago,rectifier. I would like to get it out of my way. Anyone building one or needing parts this would be a good one. These and the...

Anyone have one of these and know the hydro filter number? This is a 39 year old mower.

I'm always coming across this site when I do searches for mower and tractor stuff so I decided to join. I have an old Jacobsen GT Hydro 16 mower. If anyone here has any information on them I would like to hear from them. Right now I am in search of a regulator. These were the rectangle box...