Search results

Will a MF 2360 snow blower fit newer 1700 series as well older GC models ?

Will a MF 2360 snow blower fit newer 1700 series as well older GC models ?

Had this happen twice in the cold weather. Machine is kept in a non-heated garage. I usually let it is idle for 5 minutes before shutting off the engine. Next day throttle lever won't move. Squirted some WD40 behind the dash were cable goes into the sheath. After an hour it moves ok ........ any...

Just found a new project. 1957 420C with a Henry loader.

Any one familiar with Earth & Turf bucket blade for sub-compacts ........

northwoodpower | eBay Don't spend all your $$$$ ..... good deal on 'new' GC series tires/wheels.

Looking at buying a L650 Kubota backhoe - what Kubota tractor models would it be for ? Thanks.

I seen on some front end loders, an extra peice at the end of the tilt cylinder where it is pinned to tht bucket. Is this to increase tilt 'geometry' or ..... and also what is it called ?? Thanks Jim.

Have a 2005 GC2310 TLB - bought in spring of '06. Used to dig dirt and plow snow with the bucket. Never had need to use the PTO. Just picked up a used MF2360 snow blower for it. So I figured it would a good time to learn how to engage the mid mount PTO - first I engaged the mid mount lever to...

Looking at a new 5 foot -3 point hitch style Bobcat rotary brush mower. Any comments ? Thanks - JIM

Freind of mine is looking for little hoe for his B5100 4x4 - does anyone know the model number(s) that would fit ?? Thanks

Any thoughts on the Mahindra 5 foot - 3 point hitch rotary mower ? - looked a one on Sunday at local dealer.

We have a 2005 GC2310 TLB - our local John Deere dealer has a GC2300 with loader - mower and a snowblower (took in on a trade) ..... I was going to try to buy just the 'snow blower' - looks like it wasn't used much. What would be a fair offer - in the hot month of July ??????? Thanks.

Have a fuel hose leak right where it goes into the engine. Wire type clamp may have cut/damaged the hose.

Need part number for joystick handle for my MF 2350 loader - mine broke today close to the threaded part. Thanks .........

This fall decided to plow my garden under - used a Ford 100 sub-compact tractor plow. You might call it a single 10 inch. Once adjusted seemed work well.

Found this a week ago - Ford single bottom 12 inch plow. Model 100 for sub compact tractors.

Anybody ever try pulling a single bottom garden plow with a GC series tractor ?

Need a hydro filter for my GC2310 - who sells MF parts via internet ??

I was thinking about getting a rear mount snow blower for our GC2310. My dealer suggested a Woods Model SS52 - 52" wide blower. Anybody out there using the Woods?

How much does a GC2310 weigh with FEL and hoe installed? Anybody ever have one across the scale........thanks.

I changed the fuel filter to eliminate the "missing problem". It ran fine for 15 minites. The it started to miss again. But in Neutral it would stop. So I was finishing my task and it quit all together. Put in nuetral - started fine...ran a little and stated to act up again. It seem to have...

Has any one tried to change a GC2310 fuel filter. It is mounted on left side outer frame below the step. We have a 2004 model. Book shows a picture of of fuel sediment bowl w/a paper cartridge inside. They also show air bleed tube. Mine has no air bleed tube. And my on/off/air(?) positions are...

My tractor will miss every once in a great while -- will have a miss in the engine (like two or three times)....then runs fine for several hours. Kinda sounds like a gas motor when running out of gas. It is not consistent with any one paticular activity. Has around 120 hours. Any ideas...

Several times so far, I've driven my machine with parking brake on. The engine over powers it and goes normally. Has any one else done this? Also what will it hurt? I am thinking about mounting a switch to the pedal and putting a RED lamp on the dash to tell when it is engaged. Any ideas.......?

I am looking for a service manual for our GC2310 - does any body know where to order one??

I know this may been discussed before, but how heavy is a GC2310 with FEL and BH - no MMM ? Thanks

I am seeing some hyd. fluid leakage on our GC2310 w/MF2350 loader. Right now it is visible on both bucket "tilt" cylinder rods and drips on the bucket and floor. Any body else having this problem. Tractor has 51 hours.

I am close to my first 50 hour maintenance. Should I remove the backhoe to access the hydrostatic oil fill plug?? It looks like PTO guard may in the way.

NEED A LITTLE HELP. WENT TO INSTALL A MARKHAM TOOTH BAR ON MY NEW GC2310 TRACTOR ON AND NOTICED A 1/4" TO 3/8" GAP BETWEEN THE BOTTOM OF THE TOOTH BAR CUTTING EDGE AND THE INSIDE BOTTOM OF MY BUCKET. IS THIS HOW THEY NORMALLY FIT???

WENT TO LOOK AT OUR GC 2310TLB AT THE M.F. DEALER AND SAW A GC 2300 WITH A TACHOMETER COMBINED WITH THE HOUR METER ON THE RIGHT SIDE OF THE DASH (ABOUT SAME SIZE A FUEL GAGE). THE TLB WE ARE BUYING ONLY HAS THE HOUR METER. IS THIS AN OPTION???