Search results

I recdntly purchased a 2014 M7040 with 2700 hours on it. I bought it from the local grren dealer after he took it in on trade and I ran it around the lot for a few minutes and it ran/worked fine. The last 2-3 times that I have used it, after 30-40 minutes it begins to sputter and dies. It...

Changed the fuel filter on my 4110 this week and the ring/nut that holds the bowl in place broke in half when I tried to put it back on. Went to the dealership and got a new one and it absolutely will not fit. I even took the entire assembly off of the tractor to make sure that I had...

My 5400 has, all of a sudden, started losing power. I was moving some dirt today and realized that the rpm's weren't where I needed. I reached to adjust the throttle up and it was all the way up but I was only getting 2000-2100 rpm's. I dropped it down to let it idle and it died. I could not...

I recently removed the bucket from my loader to have some welding done to it. I noticed that one of the curl cylinders was working slower than the other. The joystick was worn out and needed replacing, so I assumed that it was causing the cylinder to work slower. I replaced the joystick today...

The help was on my 4110 today and came and told me that it was leaking oil. I went and looked and there was, in fact, an oil leak. There is a metal fitting that comes out of the valve cover and curves back down with a hose attached to it, the oil was dripping out the end of the hose. My...

I do some side work for a man that is into several different businesses. One of which was a mulching/clearing business. Long story short, the fellow that he trusted to run the mulching business wasn't to be trusted and there was a parting of the ways between the two. After a lot of searching...

Does the 4110 have to be broken in half to replace the clutch? A new clutch for mine is in the near future and I am wondering.

Today while grading my road, I noticed that my 4110 was getting slower and slower. I was driving along and drove through a wet spot in the road. The tractor just stopped, rpm's remained at the same level, tires didn't spin, didn't bind the engine up, it just wouldn't go. I switched from mid...

North of Hattiesburg do you set for a cut-off on jobs.

Does anyone know the factory thermostat temp for the 4110. Would putting a lower temp in help with cooling the engine?

My wife and I are in the process of purchasing a home and would like to pull up the old flooring and stain and seal the concrete. The main reason is my son suffers from severe allergies and carpet tends to hold dust and dirt. Ceramic or wood are way too expensive and vinyl looks cheap. I...

I am getting ready to take the loader off of my 4110 to do some other work and in the manual it says to put the loader control in the float position, but does not say what or where the float position is.

Can I put a MMM on my 4110?

How do I go about detaching my ml112 loader from my 4110 do do work without the loader? Thanks.

My 4110 is acting up. I recently purchase a 2004 4110 with 73 hours on it. Shortly thereafter, it would not crank, dealer checked the battery and said that it was bad and replaced under warranty, did not fix it. Dealer then sent a tech to my property (50 miles one way) and replaced the...

I recently (less than a month ago) purchased a used 2004 4110 with 73 hours on it from Scott Tractor Co. in Richland MS to use in my poultry houses. While using the tractor Sunday, it began clicking and would not turn over from time to time. Monday, it would not do anything, so we called the...

I am getting ready to make my first tractor purchase and have pretty much decided on the 4500. I was quoted 20K out the door and delivered for the 4500 2wd, FEL, 6' box blade, 6' disc, 6' land pride cutter(all medium duty), boom pole and 7000 lb trailer with outriggers for unloading. I will be...

Can anyone give me any info on the dependability of a Kama. I just purchasd a poultry farm and will be needing a 4wd tractor and FEL. Found a new 45 hp Kama with FEL for $14,500. Will I get burned?

I have located a refurbished Ford 3930 4wd with a FEL. I believe he said it was a 96 model, can't remember. Asking price of $13,500. Is that about average? Thanks for any help.

I have recently purchased 43 acres and 2 breeder hen(chicken not turkey) houses and am getting ready to purchase a tractor. I have a quote form my local Mahindra dealer on a new 4500, a 6' HD land pride cutter, a 6' box blade, a 6' disc, a boompole and a 16' 7000lb dual axle trailer for 16,598...