Search results

I have an electrical issue with my TN65D that has me stumped. One day all the cab electrical components worked; the next day nothing worked. I checked the large 50 amp fuse that feeds power to the cab fuse box. It looks fine. Now here's the stumper. When I plugged the 50A fuse back in the...

I have an old PHD that appears to be a Speeco. Works fine, no leaks. I need a new auger bit but all the auger bits I see require a 2" output shaft on the PHD whereas the output shaft on my PHD is only 1 3/8". Anyone know of an adapter that can fix this situation?

When purchasing used hydraulic equipment (a Gannon 4x2 boxblade with two cylinders) do I just connect it up and get busy or is there anything I can or should do about the hydraulic fluids in the used equipment?

All the augers I see on the internet have a one piece flight to which cutting teeth can be bolted. On my auger the teeth are attached to a very short piece that is attached to the flight with a bolt. This short piece also has the point on it. I need to replace the cutting blades. Anyone have...

I have a Bush Hog M446 loader with universal skid steer attach plates. The universal skid steer attach plates are attached to the loader with four large pins. If the attach plate is removed from the loader then can I attach pin-on implements to the loader? Or to put it another way are the...

sorry -- I moved this to Attachments

My 5ft shredder acts like an out of balance washing machine on spin cycle. All the blades are present and accounted for. It's the only shredder I've ever had, and it was like this when it came with the tractor. Point is that I don't know what a smooth running shredder feels like. How do I go...

The PTO shaft on my MF35 has a groove in it and light scoring where the seal rides. I'm in the market for a new shaft because I'm doubtful that a new oil seal will stop the steady drip of fluid. I've found that there are two PTO shafts available. One tends to be priced around $60 while the...

I don't have a welder but do have a birthday coming up and a wife asking what I want...:) My need for a welder will be occasional at best. I might sometimes stick some used oilfeild tubing together for a pen or tack a livestock panel to some pipe or maybe do things like weld hooks on a FEL...

Went to local NH dealer the other day for some misc. parts and noticed that all the new Blue had been moved to back of dealership. Everything up front was new Orange. When I asked why all the Blue was in the back they informed me that NH wanted them to sell only NH or not sell it at all. They...

I recently added a FEL to my 2WD New Holland TN65D and am in the process of figuring out how best to address the counterweight issue. This forum provides many effective solutions. One thing I have not seen discussed is the load bearing capacity of the front tires. My TN65D has 9.50 x 15 6-ply...

What kind of store would sell 00 grease? I have a very old 12 ft wide Servis rotary cutter with three gear boxes all of which leak slightly when using 85/140 wt gear lube.

Ha! Getting a loader added to my tractor. Hydraulics will be connected to the rear remotes via flex-lines. I don't claim to know what I'm talking about so please excuse what may be a dumb question. I have read about 3/8 and 1/2 inch lines. What size flex-lines do I need to run a Bush Hog...

Recently picked up a used TN65D. Low hours, great condition but need to add a loader. Am considering NH 32LC, Rhino 4211, and Bush Hog 446. Difference in price between highest priced loader (NH) and lowest (BH) is $600. I know only what I have read about loaders, and what I have read says...

I recently purchased a used TN65D that has 3 valves on the rear two of which are operated by the joystick. I'm going to add a loader. The NH dealer I've spoken with about adding a loader says they can run hoses to the rear of the tractor. They say the alternative --- adding mid-valves--- is...

The Onan 14 hp engine in my 2140 has a probem .... it dies after after 10-15 minutes of run time and will not restart for several hours. It has no spark when it has these episodes. After a few hours of cooling down it will then start and run just long enough to get it back into the garage...

Been looking at the 5x03s for awhile but then along comes a used low-hour NH TN65 2WD in excellent condition. Horsepower-wise a TN65 seems to line up with a 5203. When all features are considered what JD does the NH TN65 best compare to?

Was mowing around my garden this past weekend and my Cub with Onan 140 engine simply quit running. I did determine that it has no spark. Where should I start in determining what the problem is?