Search results

I was just wondering if anyone has any experience with these Galaxy Ez Rider R-4's? I currently have Titan R4's on now. They are R4's, but have a tread design of an R1 tire. I am thinking of buying a set of these Galaxies! Any thoughts...

HI, guys the front seals are leaking on my JD 4700 4x4. I was wondering if anyone can tell me how long of a job it would be to replace them? And do I need any special tools to complete the job? Guys thanks for your help!

Hi Guys! My JD 4700/power reverser lever has to be exactly in the right position in order for the tractor to start. It has some play so I generally have to wiggle the lever a bit to get it to start. Today I can not find the right spot at all. I looked for the safety switch attached to the lever...

Super S Hydraulic Fluid J2A- 2 gal. at Tractor Supply Co. Hello, Guys do think it is ok to run this (SuperTrac Tractor Hydraulic & Transmission Fluid J20A) in my front axle. (From Tractor Supply) The tractor is a 4WD JD 4700. The front seals are leaking. And I was wondering if this is safe to...

Guys I'm looking for Recommendations on a grease gun. If you have a favorite, let me know what model your using. Thanks, George

Hi Guys, I've been splitting a lot of firewood lately and I noticed the push arm on the splitter when it is retracting backwards stutters. It only seems to do it after I'm splitting for a while and the machine gets warm. Does anyone know what the reason may be? Thank you, George

Hi, I was wondering if anyone out there has ever purchased a metal garage and if they were happy with it. The one I am looking at has roll up doors. I am not familiar them. Was wondering how durable they? Or should I stick with the traditional overhead door? I am also curious if the metal...

Guys I'm stumped. I have a JD 4700 Compact that sometimes turns over and wont start. And sometimes wont turn over. And sometimes starts with no problem. I've changed Fuel shut off solenoid, starting relay, Blocking diode, Thermistor and ignition key switch. If I hot wire the starter and take...

Hello, I know there has been talk about the JD 4000 Series Fuel shut off solenoid causing starting problems. Because it was on this forum that I learned I had to replace mine. Well I replaced it and after a year it is acting up again. It seems that when I run the PTO at higher RPM'S for any...

Hi Guys, Today I was stopping and restarting my tractor a lot. Making short runs with it. Then it would not start up. My battery is old so I went and purchased a new battery. I put the new battery in and it still did not start. No Click nothing. Idiot lights were dim. I thought I would put a...

Hey guys, Does anyone know what Tractor Supply sells that is recommended for my JD 4700 front axle (4WD)? I have a slow leak in the axle seals and I want to add the proper oil level. Thank you!

I got it going guys Thank you. Fuel solenoid was backed up. Thanks! Hi Guys, My JD 4700 will not even try to turn over. Almost like my safety seat switch is stopping it. But its not that. Lights come on when I turn the key, Glow plugs light. PTO light comes on when pull the knob. But I thought...

Hi, I just recently moved off grid in the Adirondacks, I have a 1400 ft. stone, rocky driveway. I am looking for a 3 pt rear snow blower for my John Deere 4700. Does anyone have any recommendations for this type of driveway? Thank you

Hi, i need some help with my wood chipper. Today the fly wheel on the chipper stopped spinning. The PTO shaft spins. Can anyone tell me if there is a shear pin in the chipper mechanism? Thank you for your help!

Hi, I am thinking about adding a PTO clutch to my PTO that I am using on my wood chipper. I am wondering if it is advisable? What are the pro's and cons? And is it really and added insurance measure that can protect both tractor and Chipper? Thank you for your advise!

Hi guys! I have a JD 4700. 48hp (40hp PTO) I need to purchase a 3pt chipper. I am ok with chipping 4" and smaller, but I see a lot of the chippers on the market are for 16hp to 40hp tractors. Does that mean engine hp or PTO hp? And if I would exceed the hp limit could I do damage to the chipper...