Search results

I have a Titan 1206 Mower that I use with my JD 4520. I use Cat1 pins. The problem is that the lift pins on the mower are always coming loose. The mower holes are 0.9" and the Mower A fram arms are 1.3" I use a bushing in the A frame holes to reduce it down so the Cat1 pins will be tight...

I have a 2007 JD 4520. I have started to notice that I have difficulty steering to the right when the bucket is full of heavy dirt. I turn the wheel to the right but the tires do not turn to the right like they should. They barely turn (angle) to the right. It seems worse when I am going...

I am looking to buy a 2014 or older JD. I have been looking at used 4000 series. What struck me as a bit odd is that it appears as though the 4120, 4320, 4520, and 4720 appear to be the same engine except the HP goes up from 43 to 60. Same bore and stroke. Same compression (+/- .5)...

I was putting on a pair of 1.5 inch wheel spacers and almost did not notice that they were not completely slipping over the center hub on my JD 3203. Notice the gap between the spacer and the hub below. The hub stuck out 1/2 an inch. The spacer cut out inside was only about 0.4 deep. I...

I have a JD 3203 and I want to swap rims side to side so I can gain quite a bit more width but the rim hub style prevents this. Attached is a pic, showing the rim shape near the bolts which as you can see, prevents this from fitting the hub if swapped to the other side of the tractor. I...

Here is a video of a Ballast Box I made out of Concrete and a round bar. Very simple, durable, and inexpensive. DIY tractor ballast box of concrete part 1 - YouTube I plan on getting Part 2 done soon. Hope you enjoy it. Charlie

I am looking for some help in identifying the type of thread this plug has so I am sure I get the right fitting to go in its place. From what I can tell this is an 18mm ISO 261 thread (or metric ORB?) . But when I try to find a fitting for this, I cannot find it. I have looked at Northern...

I need some help from an owner of a 3120 or 3320 to take a pic for me of their PB Hydraulic Return line that is show as number 34 in the schematic below. It goes from the PB SCV to the Hydraulic tank. This would really help me to see if the same port is on my 3203 hydraulic...

I am looking to add a DIY PB Dual Spool valve on my JD 3203. JD does not make a PB kit. I am looking for a place to route and connect the "tank" (drain) off of the new spool valve. I would like to know if this line that comes from the Oil Cooler to the HST is a low pressure line that would be...

Can someone please verify the inside width of the HF QH? (inside pin to pin). I.E. minimum distance inside. I know the add says 27 3/16th but I am not sure if that is the inside distance counting the pins that go through the lift arms or just the inside width of the unit itself. I have a...

Looking for someone who has specific knowledge about tapping in to a JD3203 hydraulics system to add another function like a hydraulic top link... JD does not have a power beyond kit for this model. Thanks. Charlie

Newby question here.. Is the 3PH powered by hydraulics that is the same hydraulics pump that would run the loader hydraulics?... Hence if I bought a tractor without a loader but it has a functioning 3PH...would I have to buy a new hydraulics pump if I bought a used loader? Hope that makes sense...

I am looking at a used 97 L3300gst tractor. Are parts hard to come by? Does the L3300 share parts with a newer model like the L3400? I appreciate hearing from owners who have first hand info on this. Thank you Charlie

I am hearing that parts are getting hard to find for the 950 and 1050 models. If you owner a 950 or 1050 and you have had trouble getting a part for a 950 or 1050 please post that info here. It would help those of us who are new to owning or considering owning a 950 or 1050.... Plus, those...

Is there any difference between the 950 and the 970 besides the 970 is newer and has a slightly larger engine? (I am trying to decide which one to buy - used) I have looked at Tractor data dot com, but I was hoping to hear more from guys who really know the models.... Thank you.

I am looking for a JD as mentioned above. Must be 4x4 or MFWD. Loader is preferred. Charlie 360-703-8144

I live in Washington and I am looking to hire someone who is familiar with the 970 model to go look at it and tell me if it is in good shape. It is in McMinnville TN. Or....if you know if the dealer in the area is reputable that would be helpful to know too..... Thank you. Charlie 360-703-8144

I am researching buying a JD950 and I cannot find any literature on the lift capacity of a 950 3 Point hitch? I have read old threads and it was never really answered. Lots of guesses, which is nice, but I am hoping for some hard numbers. Has anyone seen any official JD published numbers...