Search results

I have a 4610 ford tractor, 2900 hr that has a cylinder mis like it has a bad injector. However it also won't rev over 1500 rpm. Load or no load. Has steady smoke in the exhaust at all speeds. Idles rough. Piston blowby is reasonable and it starts right up could. Air filter and exhaust seem un...

Looking for replcement cylinders for a Model 35 quik way snow blade. Does anyone know what the pin dia , bore and stroke would be for this plow? Ken

I have a saw motor running on @ 50 gpm at 2250 psi, I need to momentarily divert this flow to a double acting cylinder for a out and in cycle while the motor is allowed to coast. The motor does not need to reverse. It would be helpful if the cylinder would auto retract after the extend stroke...

I'm widening my 52 Bobcat tiller to 68 andit and my trencher also requires new bearings. I'm wondering who is your favourite online bearing supply house. Can you look up numbers online or lookup by measurements. These are just ball bearings, provided they are not some fancy oddball size. Ken

My hi flow nh ls 160 has a 15 or 24 gpm flow output. When using it on the log splitter it runs up to 600 psi inlet pressure at wot, when the valve is in neutral. The loader has 3/4 lines and the splitter valve are 3/4" ports, (rated 25 gpm flow) but the front couplers and 10' of hose to and...

Likely a :p question for the NH pro but what does the DA stand for in tn75da. I'm looking for a owners manual and maybe a service manual for this tractor. Would the manual have to be for a "da" tractor or would that be covered in the tn75 manuals? Ken

I have been thinking of constructing a backup up generator to run off the 3rd valve on my skidsteer. The 15 kw, 1800 rpm gen head calls for a 20 hp diesel engine to drive it I have 2 skidsteers that could be used to drive it. One has 16.9 gpm at 3000 psi and the other has 15 or 24 (if hi flow...

I have a skidsteer cement mixer that operates on up to 20 gpm flow to turn the mixer, I'd like to split a small portion of that flow off to control a 2" double acting cylinder with a 6" stroke to control a side discharge door. (presently run of a air cylinder that requires the air tank recharged...

I have his tandem axel trailer that uses disc brakes robbed from a 80 something GM car. The fellow who sold it to me said "GM intermediate" parts. Well I need new rotors and brakes so I ordered some for a 89 Caprice, (which I had previously matched the pads too and was told that was the donor...

Any Rv ers or anyone familar with Honda 6010 RV generator? Unit has an electric choke that stays on far to long when started in cooler weather, say 40 degrees far. it takes 2 to 3 minutes to shut off. As a result fuel is getting into the engine oil, raising the level and causing it to be sucked...

I was getting a bit tired of the time it takes to clear the parking area of my yard so I built a set of bolt on wings forward swept at 30 degrees to widen my 8' blade into a 10' I quite pleased with the performance as the plow now works as a pusher when the blade is straight and carries double...

Our 75 hp new holland has 10.5 by 20 front tires and 19.5 by 24 rears. I'd like to find some other tires sizes that would fit my wheels. There is clearance for up to 6" more radius on the rear. Does anyone know a good source of specs online to see what my options are. Tractor seems to have low...

Hello We just purchased a 300 hour 2005 tn75da with cab and fel, however the owners manual is m.i.a. Could anyone with a simular tractor send me a copy of a few pages from their manual showing what the various controls in the cab are. we have figured the obvious one out, but could use a little...

I'm looking for rebuilt injectors or a shop that could rebuild mine at a good price. Any Kubota engine parts dealers you can recomend or a injection shop that does good work at a reasonable price Thanks Ken