Search results

The brakes on our C4864 will not hold on an incline. We've been told that they are wet brakes. Has anyone had an opportunity to work on them or point us in the right direction?

Anyone had to remove and replace the power steering cylinder on a Montana C4864 tractor. We purchased an OEM cylinder from UTB. We disconnected the cylinder at the wheel but cannot see how to disconnect the end connected at the block.

I had to replace the hydraulic pump and metal pressure line going to the block. After about 5 minutes of running, I get a squealing sound from the pump area. I had that sound before the metal fluid line ruptured at the fitting which is why I replaced the pump. Do I need to vent/bleed the line or...

I had to remove the FEL to weld the support frame that broke. I looped the two hydraulic lines that were going to the FEL controller thinking that would keep the system closed, but now the 3 point will not lift. Do I need to bleed the lines or do I have to reroute the hydraulics differently...

I noticed a number of threads discussing the ETR fuse blowing causing the starter not to start. Has anyone found why that was happening? Did it have anything to do with the seat safety wiring shorting? Has anyone disabled the seat safety wiring?

I have 3 hours on tractor. It has the swivel seat with backhoe. The dash lights and glow plug work but no attempt to start when key turned to start. I noticed the seat safety wire had been crimped in the seat. I do not have a mid-PTO but could that crimped wire be stopping the tractor from starting?

Trying to find the spec on what lub oil is recommended for the final drive rear wheel hub and possibly some guidance on how to adjust the brakes. Thanks.

C4864 Ball joint broke off hydraulic steering cylinder. Does anyone have a parts manual or schematic that shows the part number? The top of the ball joint broke off & I can't locate it. Is the tie-end part of the cylinder rod? How does it attach?

Where can I obtain an operator's amnual for a C4864 or a description of the various control levers?

duplicate, sorry

Ernie, if you are there...I asked Aaron for a re-wiring diagram for the joystick on my F235, but he wasn't comfortable with the UFO system. From the attached very rough diagram can you, or anyone, provide me with some guidance. Each solenoid has two wires attached that are joined together...

I recently replaced the hydraulic pump due to cracked housing. I also replaced the filter obtained from Hoye. Now the 3pt will not operate in either direction. While the tractor is running I can manual lift the 3pt with no resistance. The UFO is not connected other then the small joystick for...

I am not using the Yanmar tiller. Is it possible to disconnect all the electrical connections from the UFO and use the lever? If so what connections would be necessary?

Do the F series tractors require a PTO overdrive? Dumb me I meant "over-run", thanks kenmac.

Tractor Ernie or anyone familiar with the F235. I've been having intermittent starting problems, but now won't fire at all. When I turn the key right to 1st stop, I get a click, then when I turn key to start, the engine turns over, but it won't fire. I noticed before when it was...

I seem to be having similiar water problems as recent threads. The tractor runs fine for approx 1st hour, but then the temp gauge approaches the "red line" and stops just before entering the dreaded area. At that time the overflow starts to blow bubbles. After shutting down, the bubbles...

Does anyone know what the distinction is between a 2 digit (ie. F/FX 24) vs. a 3 digit (ie. F/FX235) ? Most of the lists I've seen, Yanmar Owners, Hoye, etc., seem to list the 2 digit, but few, if any, 3 digit models. Harry

Does anyone know of a source for information on the operation and settings on the UFO control system on the F/FX tractors?

Rake will not stay in contact with ground when pulled over routh ground. Is there an adjustment that can be made at the 3 point hitch to provide downward pressure or is an adjustment needed at the hitch controller.

Landscape rake attached to the 3point hitch of my F235D will not stay in contact with the ground. The control on the UFO lowers the unit, but when I release the control the rake raises of the ground. Has anyone had this problem? Can the UFO be disconnected and the control switched over to the lever?

Can anyone explain the differences of the 2 series? I've been told the F/FX series is wider and are more recent models.

I'm taking delivery today of my 1st tractor a Yan F235D. I can't seem to find much info on this model. Does anyone have any suggestions or comments on this model? I have 10 ac that needs to be cleared & put into pasture for my 3 horses.