Search results

Hey all, I have an older MF 265 that is very hard to turn a tight right, but will turn to the left reasonably easy. I have added fluid to the pump a few times in the past. Often it steers okay turning in either direction when I first start the tractor up. Makes me wonder why I can turn left so...

Hey all Not sure where to post this question, but here goes anyways. I'm trying to locate a manual for a Dynesco P15 diaphragm pump we use when we burn our fence line. (My dad used to spray his fruit trees with it until he moved). Anyways, it has developed a very small leak, on what looks like...

Hey guys, I have an inherited an older MF 265. A few years ago, while baling hay, the draw bar mount managed to fall off the tractor. Anyways, managed to reinstall it and finish baling. Ever since, almost every year, I have to check the mounting bolts at least twice a year to make sure it...

Hi all. My brother inherited our fathers Kubota L245DT tractor. He would like to get a FEL that would mount on this tractor. There is only a 3 pt hitch for hydraulics, but he has located a pto drive hydraulic pump system. What makes of FEL's out there might fit this tractor, and would the pto...

Hey all. I've acquired a used PZ 2000 belt haymaker rake. I've replaced a couple of connection rods, so all turns freely. Working on the PTO shaft, the telescoping shaft is frozen (with rust I'm sure). I've tried penetrating oil, heat, put a piece of pipe through the u-joint and hammered on the...

Hi all, I have a late 70's Massey Ferguson 265 that has a pto issue. The pto won't stop turning . It engages well when I use the lever to put the pto in gear to run my bush hog, baler, swather, etc. When I disengage it with the lever, the pto does disengage, buts when I stop running the...

Hi all, Have an older MF 265 with cab (ROPS) that has a door issue. Due to a day the PO drove into an unseen hole in the field, (highways cleared out a culvert entrance that had 'filled in', the door sprung open I guess. Ever since, the door never closed properly again. When I got it, I could...

Hi all, Have an older MF 265 with cab (ROPS) that has a door issue. Due to a day the PO drove into an unseen hole in the field, (highways cleared out a culvert entrance that had 'filled in', the door sprung open I guess. Ever since, the door never closed properly again. When I got it, I could...

Hi all, newbie to the Kubota forum. I have an older B6200E Kubota I inherited from my father in law about 8 years ago. It was used pretty regularly when he had it, mowing between the rows of Christmas trees. As we no longer have the trees, it has been pretty much just sitting, used occasionally...

Hi all Have a late 70's MF 265. To my knowledge fluids haven't ever been changed. Want to change out the power steering and hydraulic fluids and filters. Have downloaded a service manual for this beast, but it doesn't state what grade the hydraulic oil or power steering fluid should be to...

Hey all, I've finally figured out a cure for my ignition fuse issue on my MF 265. History: -started blowing the 20 amp ignition fuse. Found it right after finishing cutting/raking/and baling my small hay field. - dismantled my tractor dash as much as I could (because of cab on...

Hey all, Last year, while baling a heavy crop of alphafa last year, I managed to throw a shear pin on the pto. So, carrying on I changed the shear bolt, but being rather new to baling and this machine, I forgot to put the needles back in the home position. And anybody who does a lot of hay...

Hi all, the ignition fuse on my 1970's MF 265 has started to blow. I realize I'm looking for a wire that is grounding to the body somewhere, and there aren't a lot of wires on this tractor. I've spent about 4-6 hrs. going over the wiring to no avail. (This tractor does have a cab which does make...