Search results

Do they still sell thaese? Is there a way to modify the planter? how do I change the bearing? Is there a spacer between the bearing and housing?

Not sure what year. All the numbers I could find. Thanks.

I took these photos of the corn planter I purchased. Not sure what year or model.

Just bought a Massey loader for my Massey 150. Not sure of model. Needs new hoses. Looks like hoses are attached to lower loader arms? Why? Will post model of loader later

OK! I didn't know I had to mark my clutch pressure plates before taking it apart. Will it cause all sorts of broblems? tham nks doug

Any Ideas on how the two Bellville plates should face when putting pressure plate together?

anyone put in a new wire harness for their 8N lately? I bought a new harness but some of the colors do not match the schematic in the shop manual. I have a red, black and white coming out of one end of harness and 2 reds a black and a yellow out of the other end. Which way is front? Thanks, Doug

putting my 8N motor back together. Oil hole is on the front of rod not either side(where bolts are located) Does the hole go to the front of tractor or rear.? Thanks. Doug

Draft control doesn稚 seem to work. Lever moves freely and doesn稚 seem to be engaging any other mechanisms.

I have a 1975 Ford 3000. I got that much from the numbers but cannot decipher the rest, any one help here? 5B03B C452342 thanks, doug

Bought a 2000 model ford tractor and it has taller tires. My fenders are off but when I checked the mounting the fenders touch the tires. I see some fenders have a taller mounting bracket. Can I purchase these taller brackets without having to buy 2 new fenders?

Just a question concerning 3pt on this tractor. When I engage the 3pt it either goes all the way up or all the way down. Am I supposed to be able to stop it going down at different levels? Is the an adjuster somewhere? Thanks for reading Doug

Not sure how to pull the brakes off of this tractor. Do I need to pull the axle along with the drum or can it come apart seperatley? Thanks

Just removed all pistons from this tractor and not sure if it has sleeves or not. Cylinder sizes are: #1. 3.136 #2. 3.140 #3. 3.144 #4. 3.142 Showing a couple of pictures along with measurements, looks like a lip bu do not want to start banging away if no need. Thanks, Doug

Does the camshaft just slide out or is it held in by something else?

well, I purchased this 1947 ford 2N for 600$ and have been tearing it apart one piece at a time when I have time and today I just got the oil pan off and it looks like this tractor hasn't had a thing done to it since 1947.

How do I remove the front end on a 2N Tractor? Does the bolt just unscrew?

I have what I was told a Ford 4110 but not sure. D2NN7006 XDA21722 C7NN4024 G

how is the rope trip mechanism supposed to work on this plow? When I put it back together I must have placed the trip mechanism on wrong when I pull the rope it doesn't engage anything and I have it so the wheels are lifting the plow.? How does the trip lever get positioned?

cant seem to get this to fit right. Any thoughts?

Does anyone have a close picture of how the tail wheel on a moline 2 bottom plow is supposed to look after it is on the plow? Can you send me a front and rear pic please? doug357@q.com Thanks

I have a couple of bent pieces and would like to take this apart and straigten them. Any thoughts on how to get this apart?

Not sure if there are left hand threads here or not. Input would be nice. Thanks

I just bought a Ford 4110, looks like a 3600, and the drawbar was not attached to the tractor. I am not sure if I need a pin or will a bolt do?

Hello again. I got my 3 point all rebuilt, new o-rings and adjusted to where I think it should be. It lifts great but bleeds down slowly. My actuator handle will not fit right on the lever shaft so I cannot use the handle....yet! As you can see through the pictures I have a remote hydraulic...

I got the tractor hydraulics rebuilt and placed back on the tractor but I cannot get the three point actuating lever to move.

I have drained my hydraulics and want to clean or replace the filters. Looking at the pictures, do I need to remove the gear on the right side to get to the bolts that hold the filter line in place? Looks like there is a baffle in there also. Do I remove that as well? Do I need to split the...

Can someone please tell me the location of the hydraulic drain plug on thi tractor? Also, when I fill the hydraulics, does it fill the rear end also?

Ok, well, I am rebuilding a tractor I bought from an elderly guy who started taking it apart. I am working on the 3 point linkage system and I have used most of the parts in the box except for a few bolts. It looks like in the picture something is supposed to go into this plunger but not sure...

I bought a 4110 tractor 3 cyl Gas and it has a couple of problems but not sure about them. The tractor turns over but doesn't start, no bigee I dropped it off at a mechanic friend garage. There are a couple of parts I am not familiar with but will figure them out, the 3 point lift ram and the...