Search results

Looking for ideas on how to mount my Meyers salt spreader. It's the "Mini" model, 400lb hopper, has a reciever mount. Originanlly I had planned to weld a reciever to my box blade. Then I lookd at it and realized I'll be picking this thing up to slide it on the mount. It only weighs 135lb empty...

I'm pretty sure this has been covered. I searched and searched but couldn't find my answer. I'm putting a Meyers Snowplow on my Kioti. In the past I had a smaller blade mounted up front. On that blade I fabricated most everything. I used 2 D.A. cylinders one for up down the other for angle...

Ok so here goes. I started my little CK20HST up yesterday. Drove down the hill to do some weedeating, set the brake went to shut her down but she didn't want to. I'm assuming the ignition switch is faulty. It'll start up with no issues. But I have to pull the fuel shut off to get it to stop. My...

I know this has been covered before, but I couldn't find the answer. I have a Kioti CK20hst. I recently picked up a plow truck, F-350 double cab long bed. This thing is around 30' long with the plow. I bought it for the plow and salt spreader mainly.... What I want to do is put the blade on the...

Just started plowing the drive we have around 8" of snow and a 600' drive. I ran over an old transmission over by the barn. Well all it did was catch the Hyd filter. My Kioti dealer is closed. Anybody know the replacement numbers? From Napa TSC or whereever. Please help..... Thanks. Sorry the...

Ok went to plow the 7"off the driveway. I usually run in low range until it's safe to put into high range. Well the last 2 times I've plowed I couldn't get he lever to move. Any ideas as to what's wrong? The tractor has a nice dry shed to sleep in so it's not frozen. Any help?

But not the usual..... I came across some stuff called Rumber, supposed to be stronger than wood. Cost less too. Anybody ever use it? Where'd you get it? Stuff seems like it's the answer to rotting boards.

I'm getting ready to put cylinders on my new to me plow. I've been thinking should I set the up/down so that I can actually dig down an inch or maybe two? I know My CK20 isn't a dozer but I could use it to move light material around. So what do you think?

I bought an old plow that I have now mounted to the front of my CK20HST. I'm thinking remove the FEL and plumb in an up/down cylinder and an angle cylinder. I've been looking around and the one I'm seeing seem to long, closed from pin to pin 20.25". I'd like a shorter pin to pin and still get...

I have a question I've been reading alot on snow chains here and other places. First my situation... I have a 600' concrete drive. It's all of 2 months old. The first 350 feet is somewhat flat to the last 250 feet being pretty steep hill. I'm a little worried about the hill when there is ice on...

Ok I posted a thread about the old blacktop drive being replaced with new concrete about 3 weeks ago. Now that it's completed, I have a new problem. I had them pour a pad (42' x 40') going over to the shed/barn. After a rain storm the other night I've noticed that some of the fill has moved and...

Just thought I'd tell you all about my new adventure. About 4 years ago I let a man talk me into laying blacktop down for my drive. I had planned to use concrete but this seemed so much easier. Anyway shortly after he had finished my drive had holes forming and it got worse as time went on...

Hello all, I'm getting ready to have the blacktop drive replaced with concrete. Just wanting to know what kind of labor charge I should expect? I've figured the concrete to be around 124 yards. The drive is 12' x 600' with a parking pad being 32 x 35, and the wife decided it might as well go to...

Hey all, I have around 10 bats living in the shed. I don't have a problem with them being there. Haven't seen a mesquito(SP) all year. I do have a problem with whats left over! They leave the droppings all over my workbench. Any ideas as to how to keep them around but without the droppings on...

I have a double axle 7000 pound trailer it's 16' with a 2' dovetail for a total of 18'. My truck is an '01 Dodge 2500 that sits pretty high. Now here's the problem. The trailer sits to low, even with a drop hitch the dovetail sits about 3" above the ground. I'm thimking of lifting it. The axles...

OK I made up a tooth bar. I had the 1/2x4" flat, bought the teeth and shanks off ebay, pins bought locally (those things are high for what they are). When I welded the shanks on I ran into a problem. The 1/2 warpped on me guessing to high on the amps. Had to do some major work to get it back...

The Receiever on the bucket was one of the best ideas that came from this site. I had the plate and the tube cost me 5 bucks. I have picked up my 18' trailer to the point that all 4 tires were off the ground, pretty happy with that. One idea was to make a FEL mounted boom pole. I made the first...

ere are the pics of my Hooks. I welded one on each side. I had to put some 3/16 plate under them to get em to sit the way I wanted.... again don't make fun of my welding. It's all a hobby for me. And I have never had one break. These hooks have picked up a locust tree that was around 14" round X...

Hello all I've been waiting to show just what you guys have taught me over the last few months.... I still can't post pics in the photo section so I have them in Picasa... I made the forks out of 2x3 1/4 wall tubing. I think all together they cost around 100.00 to build! I know they will at...

I'm wanting to upload some pics.... When I go into the Photos section it tells me to click upload then it comes up to either log in or register. I shouldn't have to right? I have deleted the cookies like the FAQ's suggested, but it did nothing. Help please.... Mitch

Hello to all, Just wanting to know where you got your shanks and teeth? How much did they cost. Are some better to use than others? If so why? Thanks in advance! Mitch

Just wanting to know have you or would you weld brackets for lights on the roll bar? I'm wanting to put a couple lights up there but am not sure what it would do to the metal integrity.

Hello to all, This is my first post here(I've been reading alot just didn't register), another first is my tracter(I purchased a CK20HST) never owned anything bigger than a garden "tracter" before, It's coming with a KL120 FEL, & 48" finish mower. Any way this is just a get to know you all post...