Search results

I have an 2002 Kubota 2910 that is showing a leak in the LH bucket cylinder. Looking up parts online, I found 2 "models" of this cylinder....B03002 and B03005....Both with the same PN of 7J045-64010. The model B03002 shows a seal kit PN 75545-64600 and the model B03005 seal kit is PN...

My trusty B2910 seat is starting to fall apart....after 18+ years. I intend to replace it in the next few weeks, and am looking for suggestions as to who sells the best seat....with arm rests. I want something that is well built, and will hold up for years of use....would rather pay a bit more...

I have a B2910 that I bought in 2002, and it has about 850 hrs. on it. Today, I was moving some dirt for a couple of hours, and everything worked fine. When done I drove near the house to rinse the dirt out of the bucket and when I tried to start it after sitting for 5 minutes, Nothing...

I have a nice Kubota B2910HST that I bought way back in 2002...when we retired to 40 acres of forestland. This past Winter I noticed slight oil leaks from 2 of the hydraulic cylinders on the Loader. It's not much, and just leaves a few drips on the floor of my workshop. Now that warm weather...

I have a nice B2910 with a La402 loader that I bought new in 2002, and only have about 850 hours on it. Over the past few months, a couple of the hydraulic cylinders have developed minor leaks....nothing severe, just enough to leave some oily spots on the workshed floor. I've only had to add a...

I was going to go out today and clean up a bunch of wood shavings where I had been doing a bunch of log splitting. However, when I tried to lower the implement arms to attach my landscape rake, the arms didn't move...even standing on them didn't lower them. So, I went back into my workshop and...

My trusty Kubota 2910, which I bought in 2002, is showing its age in the seat. The vinyl seat cover has developed several cracks, and I have it held together with Gorilla Tape, to keep the foam from popping out. I have found several sites on the Internet for new seats, but I would like to hear...

The seat on my trusty 2002 Kubota B2910 has just about worn out....major cracks in the seat covering, being held together by Gorilla Tape. Does anyone have a good proven source for a new seat? I found this one on the Internet, and am thinking seriously about ordering one. Has anyone dealt...

It's time to replace the filters/fluids on my 2002 Kubota b2910....it's been a great tractor. I prefer to use WIX filters, and I noticed a different PN for the hydraulic filter on the Wix website. I figured perhaps Wix had updated their PN's since this tractor is several years old. I had a...

Today, I was cutting down some dead trees in the forest, for Winter firewood. I took down a huge Oak tree, and it fell into a heavy growth of underbrush and thorn bushes. I decided to tow it to a more cleared spot to cut it up. I hooked up the tow line, and began moving it....4WD, Low gear...

In recent weeks, I've noticed a slight oil leak on the workshop floor coming from one of the hydraulic cylinders on my LA402 loader. It's not a big leak, and I'm hoping it is just seeping a bit around a seal due to this extended period of brutally cold weather. However, just in case I need to...

I've got a minor problem on my B2910....the vinyl seat covering is coming loose from the cushion. I would like to find some way to glue that down before the seat cover begins to fall apart. I am thinking about injecting some contact glue into the area with a hypodermic needle....the glue...

I had a first time experience today. I was running my B2910 steady for about 2 hrs this morning, and I shut it down for about 1 minute to get a drink of water. When I came back, it wouldn't start. It cranked over normally, and usually starts after just a couple of revs, but it acted like it...

I just finished rebuilding the front axle on my B2910HSD a few days ago. One of the Korean bearings on the Spiral Bevel Shaft (Pinion Gear) froze up and spun inside the axle housing...ruining it. The total parts cost was about 648 dollars, plus about $90 for a Kubota maintenance manual. I...

I am rebuilding the front axle on my Kubota B2910 4WD. A bearing froze on the Spiral Bevel Shaft, and damaged the shaft, and scored the axle housing. It looks like the Kubota parts cost will be around $700. I found this Chinadepot web site which imports the parts directly from China....which...

I am rebuilding the Front Axle on my Kubota B2910 4WD. A bearing froze up on the spiral bevel gear, and damaged the shaft and scored the axle housing. I'm looking at around $700 in parts from Kubota. I found an Internet supplier which gets its parts directly from China....which is probably...

Has anyone ever removed/rebuilt the front axle on a B2910? 3 or 4 weeks ago, I was coming back from the neighbors house with a load of firewood in the loader. I was on a gravel road, 4WD/Hi Range, and driving only abour 3 MPH. Suddenly I heard a loud noise, and the front axle locked up hard...

It is my understanding that starting in a couple of months, Diesel fuel is going to be substantially changed. The refineries, under rulings by the EPA. are going to start supplying USLD (Ultra Low Sulphur Diesel) which contains no more than 15 PPM Sulphur, as opposed to the current fuel which...

I have a 2002 Kubota B2910HSD with a LA402 Loader. Its been virtually flawless, however I have one minor problem. The flexible hydraulic lines going from the Loader Joystick to the metal lines on the loader frame rub the paint off the rear hydraulic cylinder. The lines are encased in a tough...

B2910HSD won\'t start I have a 2002 B2910HSD with about 180 hrs on it. In the past couple of weeks, I have had a strange trouble that has me stumped...perhaps someone else has run into this. One two occasions, while digging dirt, with the FEL, to fill in around the yard, I have killed the...

My B2910HSD is starting to show some signs of serious work. Its been a workhorse and while I haven't abused it, I haven't babied it either. With winter coming on, I've been thinking of doing some serious cleanup, and touching up some of the scratches. Does anyone know of a good source of the...