Search results

As the title says, my dad's Jubilee's lift works up and down with the lever as it should, no shaking stopping or hesitations. However, I only have a draw bar and welded receiver hitch on the 3 pt and that's about all it can raise. If I hop on the the drawbar attachment, it can't lift my paltry...

My dad picked up a Jubilee several years ago, drove from the auction and parked it in my yard. I've done a few things over the years to keep it running but it had a 3pt lift that functions up and down but will not lift my miniscule 230lbs. So it hasn't done anything and his health has been going...

Picked up an older rotary mower for a couple hundred bucks that I know needed some cracks welded and bolts to the gearbox/deck tightened....but it did have a new back wheel :D Anywho, I suspected it would probably need seals. After welding cracked reinforcements, cracked areas around gearbox...

I've had a project waiting under the barn and getting to it now. Tecumseh 13hp exploded years ago. Recently picked up a 15.5hp Briggs for $100 off craigslist. Its bolted up with belts on and will work out the muffler issues later. Murray's electrical wiring still intact and have the wiring...

Looks like I might need to replace the bladder in my Sears Captive air tank, 36 gallon and about 10 years old. Pumps been coming on sooner than should and I've noticed air in the faucets( say if flush a toilet pump is on immediately. I haven't noticed any water coming out thru air valve on tank...

Have been working with a guy to take a shed off his hands. I'ts 12wx24Lx12'8"H. Too long & heavy for my dad's 16ft trailer, so the only guy around that could do it needs me to remove the roof. Will have to cut out the apex of the truss as well to lower it. I'm hoping to just remove the...

Decided just to use a simple bracket attachment rather than buying the bracket sold for the tractor. Not much to look at but hopefully it'll do. All connections soldered, taped and shrinktubed. Wired into lines made for worklight. Think I'll get one for other side too, may go with a high mount...

I have a large piece of red oak I cut on an alaskan mill with the intentions of putting up a mantle. It's massive now and will still be massive by the time it's cut down to about 7 1/2 ft by about 16 in wide. It's 3" thick. The idea is to drill the stones to mount some anchors or do large...

Hey everybody, I've searched the forums with no luck...tried everything from a to z. So thought I'd just post the question in case I got the right viewer with all the answers. I would like to swap out my Marvel Schebler to a Zenith carburetor. No matter how much cleaning/rebuilding/parts...

Have a small 800 sq. foot house which the roof comes out to about 10 sq. Pretty straight fwd gable roof, no hips or valleys, no dormers, no skylights, no chimney. Two 2 inch air vents in the back, one small transition for the front porch, pitch is probably 3.5/12. Its an old house that has had...

Thought I would post some pics of the sickle bar pruner rig I made to go onto the New Holland T2410 tractor w/ SSQA loader. Sorry I didn't take pics along the way like all the good detailed guys on here do but it was all I could do just to get it built. I'll post better pics after she's been...

Where would be a good place to get the nonstructural parts to a pruner such as this? Pumps, pulleys etc. If one were to build it himself Farm equipment,Bubco Home Hedge Trimmer Or parts for something like this? Little further down on page COLLARD MINI-LEM FRONT LOADER KIT

Wife wanted this old project trailer relegated to the very backyard. Haven't had much time to work with this tractor yet but thought I'd share a little. Although the pic is labeled grapple, its really just a fork/frame attachment. Tom

Just curious how everyone else keeps their rear remote engaged. I've tied my old JD 4010 off to the back of tractor with twine. I'd like a less primitive way to do it on my new T2410. Just lookin for ideas. Tom

Was quoted $2150 for Markham's 66 or 75" grapple rake and forks/frame delivered. I didn't verify but I assume this does not include hookup hydraulics. I have two rear remotes which I would uitilize to run the grapple. I'm sure this would pay for itself in a year but wondered if anyone knew of...

What price should this go for? Supposedly an 08, less than 5 hours, one remote in back, 270 front loader, and EHSS. No canopy, industrial tires, weighted w/ ballast. Tks for your replys. This is expected to be zero%, 59 months. I understand this to be a same item as the new 4055. According...

What's would this bring? Its not mine but maybe it will be. I boy can dream.... It looks to be in GC with no flaws that can be seen. 2004 model. 1. New Holland TC48DA Boomer Utility Tractor 4 x4 Turbo Diesel Engine, 12 x 12 Shuttle Transmission, Variable PTO Drive with a three point hitch. 2...

Just was wondering about how common or not that people are financing some new machines now or even used ones. The 3 I own, were used ones when bought, I paid cash. Granted they are old as dirt but have done their job to this point. I'm looking at getting rid of my JD 4010 as I no longer need an...