Search results

Hi all, it has been some time since I posted anything. I lost a pivot pin on my LJ200 loader (lower most front). I can not seem to find a P/N anywhere on the web. Does anyone know of a good dealer who has parts diagrams and can get this item? My dealer is long gone and being up in the northeast...

Anyone install a third function remote for operation of a Grapple? I see lots of options noted on the forum but no TYM 273 owners. I have the factory backhoe installed as well. Thanks

My temperature gauge starts midway on the gauge upon power up, prior to actually running. Once started it jumps up to the upper limit in minutes. I suspect a faulty device, not sure if it is sending unit or gauge. Any ideas on how to identify the culprit?

I have a NIMCO 11087-2S remote loader valve that needs repair. The rear retainer clips are corroded and bind so I need to replace them or replace the valve. I can not seem to find parts or a recommended replacement online either. NIMCO does not list this valve on their site anymore. Any...

My joystick will not advance the lift portion of the loader valve. The tilt portion is operational. Anyone have or know where I can get an exploded parts diagram of the valve. I'd like to know what I am getting in to. Any thoughts on diagnostics, repairs would be appreciated.

I had my transmission to HST drive shaft go a while back and replaced it with the newer style. Now after pushing RI snow all winter my front drive shaft appears to be shot. I did not remove the shrouds yet to look at it due to weather but it is loose and spinning (or not spinning) in 4 wheel...

All you 273 owners, check the drive shaft between the engine and HST. If you do not have universal joints I strongly recommend getting to your dealer and getting the the new design installed BEFORE the shaft lets go. Notice I said BEFORE. As mentioned in a previous thread the original design of...

I don't really want to pile on or become a TYM basher but I figured I would alert you 2xx series owners to a few recent issues. 1. Gauge cluster failure - my dash gauges just quit working - solution warranty replacement. 2. Blown hydraulic steering hose - I had heard folks comment on hydraulic...

I have a Nimco control valve for my FEL with the following info: 11087-2S K2 M07A0002 I am looking for a schematic for the control. It has 7 connections 2 go to the transmission (pump), 4 to the FEL and 1 goes to an unknown location. It is routed under the machine and I can't trace it until I...

Just dusted off the machine from winter and have run into some annoying issues, maybe someone can give some advise. I have a 273 with a factory backhoe, I am getting leaking from the hydraulics tank cap when using the BH. I had a severe problem last fall and switched the lines, this helped. I...

I am investgating installing a snow plow in place of my bucket to make my snow removal a bit easier. I have seen some great ideas in the attachment forum. I am looking for a few TYM specific ideas. 1. Has anyone added the optional auxiliary hydraulic take off? I understand it is a dealer...

Winter Preparations This will be my first winter with my TYM 273. I have a FEL and backhoe and living in New England I suspect I will be clearing snow or continuing to work in the woods. What can I do to insure my tractor starts regularly and how long do they need to warm up? It will be...

Winter Preparations - 273 This will be my first winter with my 273. I have a FEL and backhoe and living in New England I suspect I will be clearing snow or continuing to work in the woods. What can I do to insure my tractor starts regularly and how long do they need to warm up? It will be...

I recently purchased a TYM 273 with FEL and factor backhoe. When using the backhoe I have noticed hyd oil coming out of the breather hole of the tank cap. I swaped out the cap and it still came out. I then plugged the hole and the fluid came out the breather tube. This does not happen with the...

I recently purchased a TYM 273 with FEL and factor backhoe. When using the backhoe I have noticed hyd oil coming out of the breather hole of the tank cap. I swaped out the cap and it still came out. I then plugged the hole and the fluid came out the breather tube. This does not happen with the...