Search results

I have some 500 Brinell 12" circle steel plates and I'd like to make a target frame for them. I'm thinking of rebar legs to push into the ground with a horizontal piece to press your foot on. Then rebar on the top. I'll either have pipe on the top rebar and weld a tab on the pipe to bolt to...

I just picked up a 30 gallon fuel caddy off of Craigs list. It was used with gasoline and I want to use it to fuel up my Bobcat. I have drained out all of the gas and have the bottom drain hole open along with the refill opening. I plan on leaving them open a day to 'dry' out the insides...

Please let me know if this isn't the correct forum. Please watch this video for the issue I've having. I just picked up a used Mackissic 12P chipper shredder. Mackissic 12P :: 12p.mp4 video by vabeltfed - Photobucket Problem is the engine runs for several minutes and then throttles down...

I'm about to do the 50 hour service this week and have a question. I believe I have everything ready except while re-reading the manual, I see the front differential fluid amount say 4.75qt's (each.) What does the each mean? I picked up 5 quarts of fluid and now wonder if I needed to double...

I just installed the rear remotes in my CT235. Which connectors do I purchase so they will properly fit into the quick disconnect couplers? Also, which hose size do I purchase for my hydraulic side link? 3/8, 1/2? I'm researching the parts right now and once I place the order for the side...

Well, I attempted to install the rear remotes this afternoon. Instructions said 1 hour. I started at 10am and just wrapped up at 4pm. Still not finished. Instructions were lousy and I was missing one of the black o-rings. The 2 circular rods you install in the first step, one was warped...

My CT235 didn't come with rear remotes, but lately I kind of wish I had at least one for controlling the side to side pitch of my rear blade. (Getting tired of cranking) Since I only have a rear blade I don't see a need for the toplink but if I were to get 1 remote, I'd probably get both now...

I'm looking for a chipper shredder, something better than the lousy 5-8hp engine ones which can't even chip a 1" branch unless it is dead. Anyone have or know of any vidoes of this model working? I'd like a nice Wallenstein 42 but I'd like to have the shredder. Also, it says 10-30hp and...

I see that my CT235 has the bullet connectors under the right rear area for a work light. Are people using some sort of flood light or just a normal "work light?" This one looks nice but would it work well and it is also 55 watts. Is that too much (watts.) Dual Beam. I can only see...

Hooray for me. :) I finally have a real tractor, no more Iseki tractor I was too big to sit on. Plus no more 2wd and grinding gears. Lol, when they dropped off the 235, they couldn't put the Iseki in gear. I had to drive it up the ramp for them. I received the 7TL loader, filled R4...

I've read lots of R1vsR4 tire threads and I'm just about to buy my new tractor. Probably a Bobcat CT225/230 or 235 I have 1000' gravel driveway with one medium sized hill about 200' long. I have to grade it after each heavy rain and my current 2wd with FEL 16cyl tractor with R1's can't pull...

Can I get the length of the tip of the loader 7TL loader (Bobtach) to the ends of the 3pt arms. If you have a back blade, can you add in those dimensions too. (2 different lengths please.) From the flyer I have the length of the 225/230/235's are 122.2" It says with 3pt but I'm not sure if...

Has anyone replaced the Key start with something like a few rocker panel switches? The only key I have looks about to break in two so I've been thinking of just taking out the key portion anyway. If anyone has done this, was it easy to wireup the switches? Since my key controls the start...

Iseki 1610 I replaced the fuel filter and that was extremely dirty. I have about 20 hours on the tractor since I purchased it last fall. 900 hrs total. No problem removing the filter and putting in the new one. I filled the bowl up with diesel fuel and tightened the top. Ran the tractor...

Iseki 1610 Tractor. I was attempting to replace the Hydraulic fluid and low and behold I unscrewed the transmission plug. It was a brown fluid. I knew it wasn't hydraulic once it was almost overflowing the 7qt bucked I had below. Hydraulic fluid should have been only 5.8 at the most. I...

Can someone list the fluids (what type of each and how much) for the Iseki 1610. As of right now I have no clue on where each fluid is located and will soon need to replace the Hydraulic fluid. I have a manual coming and will look through that but I hope someone already has the info needed.

I'm interested in getting a FEL on my little Iseki 1610 tractor. 2WD, not 4wd. As of right now I use the tractor for grading a 1300 foot driveway with gravel. The only way to move gravel around a distance is to get a load of gravel in a truck and shovel it out at certain areas. Or use a...

I've read numerous posts about this but I'll ask again. We have a gravel driveway about 1500 feet long. It is rolling, up and down a few small 3' hills and up a larger 100' hill. We have always had crush-n-run gravel dropped. Once packed down with a little rain, it is extremely solid...

Where does one pickup the corrigated tin roof panels? I've seen a few of you build pole barns or lean to's and I'd like to put some up on a lean to I'm building. Does Home Depot or Lowes carry it? I'm in Northern VA if that helps. Thanks.

How do I attach the 3 point hitch to this axle? The bottom has 2 rubber plugs in where something can attach but I need to attach the lifting? bars somewhere. You are looking up from the bottom.

The TS1610 came with a roto-tiller attachment. I don't need that at all but I suppose I can eventually use it. I need to put a 5' grader blade on for repairing a gravel driveway and ocassional snow removal. What do I need to be able to attach a blade to this tractor? The setup looks a...