Search results

My ign switch is rusty and although it turns it does not work. I jumped the start wires and the wires are OK. Does anyone have a wiring diagram so I can get it running while I wait for a new switch. I only need run and start functions, I can put a separate start push button in it if needed. Henry

My selector valve is leaking out of the lever shaft and wonder if anyone has rebuilt one and had good results? Could not find a breakdown for the valve. Any help would be appreciated, thanks, Henry.

Tried to delete this post Would someone tell me how to delete a post. Thanks, Henry

The fel valve on my M/F 2310 is leaking and will not hold up when in neutral, plus the float does not work, the lever just drops into neutral. I called the local dealer and can get the two seal kits for about 100$ and I hope the detentes are not worn. I know they buy their valves from an outside...

I was given a 90 316 today and we could not find where to unlock the diff to push it so we put it on dollys and then dragged it onto the trailer. Would someone please tell me where the lever(?) is, not visual like my other JD's are, thanks, Henry.

I did some searching on the great internet but came up short on finding filter numbers for the oil and Hyd systems. I did find a wix for the air, 49691. Has someone found other brands besides AGCO and have numbers to share? I have a Fram box from the PO which is PH2921 but no cross dimensions to...

We have a rain/ snow water pond and when it is full it runs into the neighbor's along a normally dry creek and over to the main creek. Our land is lower than the pond/ creeks and the spring water runs our way and it is very wet. I have quite a few trees cut and saved and thought about building...

2310, for a while I had to wiggle the switch lever to get the headlights to work. The other day they did not work but the tail and gauge light I installed did work. So here I am thinking I will have to wire in a toggle sw and bypass the MF switch but then I took the MF switch apart and it was...

I tried a search for block heaters but came up empty. What is the dia of the block heater I should get? I want it on hand before I drain the coolant, thanks.

The PO welded a smoothing plate onto the teeth of the BH and I want to remove the plate but do not want to cut off anything that should stay. Here are some pic's, thanks.

I will be storing my 2310 outside under the lean-to and would like advice on what you do to winterize the tractor. I will be checking the anti freeze strength and putting something in the fuel(what do you use). Any other advice? Thanks.

This is a tour of a private collection, open to groups by request. We did not make it to here and am still crying, pictures are not the same as being there. Tackaberry Tour October 24, 2010 - 6one3's Photos | SmugMug

I went to put the backhoe on yesterday for the first time since I took it off early spring, I have never put it on. I could not get the lower arms close enough to the tail to get the backhoe into position as the hoe frame pushed against the arms and stopped it from inserting the pins. Would...

I went out this morning to move some dirt and the bucket would not tilt all the way back but it would dump, so I did 2 small loads. I removed the two pins that hold the cylinders to the top of the bucket and the bucket swung freely. I tried the tilt and the cyl'ds would not move???? As I was...

I checked today with the dealer and they can only get the 2400 series shop manuals, does anyone have a 2300 they no longer need? Thanks.

I am looking for a wood splitter and would like your opinion on whither to get a stand alone splitter or a 3PT hitch splitter. There is a 3PT splitter used near me for 675$. Thanks. 3 point wood splitter - Ottawa / Gatineau Farming Equipment For Sale - Kijiji Ottawa / Gatineau

I am looking for a wood splitter and would like your opinion on whither to get a stand alone splitter or a 3PT hitch splitter. There is a 3PT splitter used near me for 675$. Thanks. 3 point wood splitter - Ottawa / Gatineau Farming Equipment For Sale - Kijiji Ottawa / Gatineau

I have seen the videos on using a BB but I don't see anywhere that tells me what setting to put the 3 point hitch in while leveling. I have wash board on the laneway and want to level it and have a slight crown. Do I set the box on the ground and then lock it, do I dig it in a bit and lock it...

Has anyone installed lights in the tach and fuel gauge pods. It looks like the holes are there and I have a few light sockets from other gauges that may fit. Thanks