Search results

Thanks to Barton Tractor of Karns City, PA for being kind enough to inform me that my tractor had a recall on the EZ shift mechanism on my tractor even though I didn't buy it there. (Bought a new Bad Boy CZT Elite zero turn there :cool2:) They were kind enough to offer assistance in getting the...

Has anyone seen this video? I came across it while looking on YT. R3039 frame modification - YouTube

Heres how I did my ROPS LED bar

I was mowing today and was making turns when I noticed that there is no steering stop. When it turned the wheel all the way left or right the steering wheel did not come to lock. I could just keep turning the steering wheel even though the wheels were at full turn. Never noticed that before...

Get them while there hot.. LS may have them taken down!! Northumberland Tractor Parts Ltd, Hastings, Ontario, 1-705-696-2300

Here is where I put mine.. mostly used as phone charger. Has blue LED inside socket.. matches tractor nicely.

LED light bar that I just finished up. Little bit of welding to make the mount brackets Air filter monitor TnT Kit New Holland toolbox kit

I installed one of those air filter monitors into the plastic housing that holds the air filters.. works pretty good.

Ok.. the tractor has 180 hours on it and noticed what I think may be a problem with the loader or hydraulics. While using loader to push snow piles today I noticed the following: When I rolled the bucket all the way do dump snow I noticed that there was about a second and a half delay just...

Took about 10 minutes to install. Just goes over the ROPS bolts then reinstall nuts. The toolbox has a slot in the back where a metal tab from the mount passes through. A small lynch pin holds the box on the mount. If you need to remove the box.. pull the pin and its off.

Was wanting to mount a toolbox (havent seen any ideas that I like) and thought to myself.. LS makes NH.. so I checked NH website for the Boomer 40 which is the LS R4041. They list a toolbox kit for the Boomer. Im wondering if it would fit my LS? Any thoughts? heres the link.. Official New...

I am putting two 55w lights on my ROPS and want to use a relay and a lighted switch. I want the switch to have power to it when the key is off. I have searched TBN for diagrams but have found nothing that suits me. Just looking for a simple diagram that has 2 lights, one relay, one inline fuse...

Only way I can figure out to do it is to disconnect your battery and wait until 12 noon or 12 midnight. Gotta keep battery disconnected for about 5 minutes for clock to go to 12:00.

I bought a couple of these lights to mount to my ROPS. They run off a 12v cigarette adapter plug. I have already installed a plug wired to a keyed power supply. The lights are 55w each. I want to run them off the adapter for a while before I decide to hard wire them. Would it be too much of a...

What do you guys do with your hydraulic top link when you have nothing attached to 3pt? Looking for some ideas that dont involve removing the top link. There is a hook on the tractor now that I use to hold the top link up and out of the way. Obviously, the hook wont fit a 2" hydraulic cylinder..

For guys considering having Rimguard installed... I had a tire dealer come and install it yesterday on my R4041. Each rear tire took about 50 gallons give or take a few gallons. The cost was $3.00 / gallon + $75.00 service call to my place + tax. Total was $397.50. At 11 Lbs / gallon, I added...

Does anyone know how to change the time of the clock on the dash? Mine is wrong and I cant find any mention of it in the manual. Thanks in advance.

New LS R4041 EZ. I notice when I apply the brakes, the parking brake light on the dash illuminates. I have tried to manipulate the parking brake lever up and down and the light still comes on when I apply the foot brakes. The lever is down as far as it will go. Anybody else have this problem...

Got a package in the mail today from Sandy Lake Implement. I opened it to find a nice ebroidered LS baseball cap, LS coffee mug, and LS fabric tote bag. Nice freebies!!

Needed a pto sleeve and stopped in. Never been to this dealership. On the way out.. decided to take a look at the Boomer line of tractors they had in showroom. Now keep in mind that I just took delivery on tue of my LS R4041 EZ. I walked over and looked at the Boomer40. I have heard that LS is...

Checked LS today and saw they finally updated their site with the new models.. bout time!!

Called the dealership (Sandy Lake) toady to get a recent quote on an R4041 for the bank. He stated that the tractor has 3 transmission options: standard shuttle EZ shift and hydro. He quoted me a price on the shuttle of 18990.00 plus tax for a total of 20129.00 I went to the credit union an got...

Here are some pics of the new model that took place of R4010. I will try tp post more..